Graphics Video Card for RC2014
author: maccasoft
2 layer board of 3.90 x 1.96 inches (99.1 x 49.9 mm)
Uploaded:
March 11, 2018
Shared:
March 13, 2018
Total Price:
$38.25
Add-on board designed for the RC2014 computer to provide graphics capabilities.
| Parts List | |
|---|---|
| R1, R2, R16-R31 | 4.700 ohm ¼ watt |
| R3 | 1.200 ohm ¼ watt |
| R4 | 33.000 ohm ¼ watt |
| R5, R7, R9 | 510 ohm ¼ watt 1% |
| R6, R8, R10, R11… |
Show full description
Add-on board designed for the RC2014 computer to provide graphics capabilities.
| Parts List | |
|---|---|
| R1, R2, R16-R31 | 4.700 ohm ¼ watt |
| R3 | 1.200 ohm ¼ watt |
| R4 | 33.000 ohm ¼ watt |
| R5, R7, R9 | 510 ohm ¼ watt 1% |
| R6, R8, R10, R11… |
Show full description
Teensy 3.2 based RJ45 Stepper Control
author: Isocor
2 layer board of 1.89 x 2.55 inches (48.0 x 64.8 mm)
Uploaded:
March 12, 2018
Shared:
March 13, 2018
Total Price:
$24.05
This is the control board for 8 stepper motors. Each RJ45 connector supplies GND, Step, Direction, and a signal line from a limit switch at the motor. Each motor driver is attached to the motor. Using ethernet cables to easily transfer data signals from Teensy to motor drivers.
This is the control board for 8 stepper motors. Each RJ45 connector supplies GND, Step, Direction, and a signal line from a limit switch at the motor. Each motor driver is attached to the motor. Using ethernet cables to easily transfer data signals from Teensy to motor drivers.
0008196 Rev A
author: Ulie-Under
2 layer board of 2.25 x 2.25 inches (57.2 x 57.2 mm)
Uploaded:
March 12, 2018
Shared:
March 12, 2018
Total Price:
$25.30
Bare PCB for 0008129 Rec C
Bare PCB for 0008129 Rec C
Pi IR
author: AndiceLabs
2 layer board of 1.26 x 1.11 inches (31.9 x 28.1 mm)
Uploaded:
February 07, 2018
Shared:
March 12, 2018
Total Price:
$6.90
GPIO Blaster and Receiver for the Raspberry Pi
GPIO Blaster and Receiver for the Raspberry Pi
Adapter AT keyboard to PS/2 mouse + keyboard
author: keropi
2 layer board of 0.61 x 2.04 inches (15.4 x 51.9 mm)
Uploaded:
March 11, 2018
Shared:
March 11, 2018
Total Price:
$6.15
Rio444 's adapter : https://www.vogons.org/viewtopic.php?p=647811#p647811
- use 0.8mm board thickness
VT1 ,VT2,VT3 : MBBT3904 transistors * R1,R3,R5,R6 : 4,7K (marked as R) * R2, R4 : 2k (marked as 2k) * C1,C2 : 220pf (marked as C) *
more assembly info: https://www.vogons.org/view…
Show full description
Rio444 's adapter : https://www.vogons.org/viewtopic.php?p=647811#p647811
- use 0.8mm board thickness
VT1 ,VT2,VT3 : MBBT3904 transistors * R1,R3,R5,R6 : 4,7K (marked as R) * R2, R4 : 2k (marked as 2k) * C1,C2 : 220pf (marked as C) *
more assembly info: https://www.vogons.org/view…
Show full description
EM9304-Breakout.kicad_pcb
author: mringwal
2 layer board of 0.91 x 0.91 inches (23.0 x 23.0 mm)
Uploaded:
March 11, 2018
Shared:
March 11, 2018
Total Price:
$4.10
Breakout board for the half pitch EM9304 module, v0.2 Allows to connect it via jumper wires to any development kit.
Breakout board for the half pitch EM9304 module, v0.2 Allows to connect it via jumper wires to any development kit.
SigGen
author: amateurasu
2 layer board of 2.65 x 1.80 inches (67.3 x 45.7 mm)
Uploaded:
March 11, 2018
Shared:
March 11, 2018
Total Price:
$23.85
MW-003 v2.0 Signal Generator
MW-003 v2.0 Signal Generator
9VPulser
author: BattleToad
2 layer board of 2.37 x 1.38 inches (60.2 x 35.2 mm)
Uploaded:
February 18, 2018
Shared:
March 11, 2018
Total Price:
$16.35
20GHz frequerncy divider
author: Mr-Megawatt
4 layer board of 1.00 x 1.00 inches (25.3 x 25.3 mm)
Uploaded:
March 11, 2018
Shared:
March 11, 2018
Total Price:
$9.90
4 - 20GHz x1000 frequency divider based on the ADF5002 (x8), HMC394 (set to x25) and MCP100EP139 (set to x5). All capacitors are 0402. Capacitors on exposed RF traces are 1nF, all others should be 330nF or more (1uF recommended). U4 is a 3.3V Torex XCL202. D1 is any SOD123 5V6 Zener. Output is AC…
Show full description
4 - 20GHz x1000 frequency divider based on the ADF5002 (x8), HMC394 (set to x25) and MCP100EP139 (set to x5). All capacitors are 0402. Capacitors on exposed RF traces are 1nF, all others should be 330nF or more (1uF recommended). U4 is a 3.3V Torex XCL202. D1 is any SOD123 5V6 Zener. Output is AC…
Show full description
