SNES Dejitter by Marqs
author: Helder
2 layer board of 1.74 x 0.94 inches (44.2 x 23.8 mm)
Uploaded:
January 18, 2018
Shared:
January 18, 2018
Total Price:
$8.15
This is the PCB to dejitter the sync signal of the SNES to work properly with modern TV's and Image Processors like Marqs's own Open Source Scan Converter (OSCC).
https://github.com/marqs85/snes_dejitter
Bill of Material:
U1 ATF1502AS-7AX44 TQFP-44
Y1 21.477272MHz Crystal HC49-U Ver…
Show full description
This is the PCB to dejitter the sync signal of the SNES to work properly with modern TV's and Image Processors like Marqs's own Open Source Scan Converter (OSCC).
https://github.com/marqs85/snes_dejitter
Bill of Material:
U1 ATF1502AS-7AX44 TQFP-44
Y1 21.477272MHz Crystal HC49-U Ver…
Show full description
Joy2PS2_mini_v3
author: spark2k06
2 layer board of 1.02 x 1.87 inches (25.8 x 47.4 mm)
Uploaded:
January 18, 2018
Shared:
January 18, 2018
Total Price:
$9.45
PS/2 mapper from DB9 connector and multiple protocols, using atmega 168/328 at 8Mhz internal clock.
https://github.com/spark2k06/zxuno/tree/master/joy2ps2/mini_v3 http://www.zxuno.com/forum/viewtopic.php?f=63&t=1964
PS/2 mapper from DB9 connector and multiple protocols, using atmega 168/328 at 8Mhz internal clock.
https://github.com/spark2k06/zxuno/tree/master/joy2ps2/mini_v3 http://www.zxuno.com/forum/viewtopic.php?f=63&t=1964
Kindle 3 serial plug
author: Moojuiceman
2 layer board of 0.75 x 0.51 inches (19.0 x 12.9 mm)
Uploaded:
June 18, 2017
Shared:
January 17, 2018
Total Price:
$1.90
A plug to connect the serial ports (bottom side connector) on the Kindle Keyboard (K3) and provide external access. Requires logic level shifting to 1.8V with 115200 baud rate. Connect the SHORT pin to GND to provide 1.8V on the top side connector, which could be used as a reference voltage or po…
Show full description
A plug to connect the serial ports (bottom side connector) on the Kindle Keyboard (K3) and provide external access. Requires logic level shifting to 1.8V with 115200 baud rate. Connect the SHORT pin to GND to provide 1.8V on the top side connector, which could be used as a reference voltage or po…
Show full description
10Pin_RJ45_Adapter
author: marshall
2 layer board of 1.49 x 0.79 inches (37.7 x 20.0 mm)
Uploaded:
January 23, 2016
Shared:
January 17, 2018
Total Price:
$5.80
10Pin Gadgeteer Connector to RJ45 Adapter (Pins 3 and 6 Omitted)
10Pin Gadgeteer Connector to RJ45 Adapter (Pins 3 and 6 Omitted)
Mini Flamingo Rev A
author: paulwb
2 layer board of 1.48 x 0.97 inches (37.6 x 24.5 mm)
Uploaded:
January 15, 2018
Shared:
January 17, 2018
Total Price:
$7.15
Small (1.5" x 1") ATTiny85-based driver for on-board APA102C RGB LED.
- 3 buttons.
- ISP.
- Header available to drive more APA102Cs.
- Two M2 mounting holes.
- Red power LED.
BOM cost with OSHPark boards (2-layer, non-swift) about $7 before shipping.
KiCAD files on [Git…
Show full description
Small (1.5" x 1") ATTiny85-based driver for on-board APA102C RGB LED.
- 3 buttons.
- ISP.
- Header available to drive more APA102Cs.
- Two M2 mounting holes.
- Red power LED.
BOM cost with OSHPark boards (2-layer, non-swift) about $7 before shipping.
KiCAD files on [Git…
Show full description
BLMAMount.zip
author: cstalsworth
2 layer board of 0.26 x 2.31 inches (6.6 x 58.6 mm)
Uploaded:
November 25, 2017
Shared:
January 17, 2018
Total Price:
$2.95
Sinclair - RC4 - Tented
author: ArduinoEnigma
2 layer board of 2.05 x 3.94 inches (52.0 x 100.0 mm)
Uploaded:
January 17, 2018
Shared:
January 17, 2018
Total Price:
$40.30
makeymakey-v2.1.1
author: jfryar30272
2 layer board of 3.71 x 1.91 inches (94.2 x 48.5 mm)
Uploaded:
January 16, 2018
Shared:
January 16, 2018
Total Price:
$35.40
Makey Makey board based off of Jay Silver and Eric Rosenbaum's original design through the Open Source Hardware licence.
Makey Makey board based off of Jay Silver and Eric Rosenbaum's original design through the Open Source Hardware licence.
TL866 TSOP48 to SOP44 Adapter
author: skum
2 layer board of 2.12 x 1.38 inches (53.8 x 35.1 mm)
Uploaded:
January 08, 2018
Shared:
January 16, 2018
Total Price:
$14.60
Adapter plate for TL866 programmer when only a TSOP-48 version of a SOP-44 chip exists in the programmer software, example is the MX29LV160T flash. It is designed to be used with the "original" TSOP-48 base plate and the "original" SOP-44 adapter board.
You need two 2x12 male pin headers with …
Show full description
Adapter plate for TL866 programmer when only a TSOP-48 version of a SOP-44 chip exists in the programmer software, example is the MX29LV160T flash. It is designed to be used with the "original" TSOP-48 base plate and the "original" SOP-44 adapter board.
You need two 2x12 male pin headers with …
Show full description
Pep Audio 1.2
author: citrus3000psi
2 layer board of 0.73 x 1.03 inches (18.5 x 26.0 mm)
Uploaded:
January 12, 2018
Shared:
January 16, 2018
Total Price:
$3.70
Saturn/PS1/3DO toslink board.
U1: TC7W04FK,LF
C1,C2: 0603 .1u
Saturn/PS1/3DO toslink board.
U1: TC7W04FK,LF
C1,C2: 0603 .1u
8 Pin Mini Din
author: citrus3000psi
2 layer board of 0.68 x 0.43 inches (17.3 x 10.8 mm)
Uploaded:
January 16, 2018
Shared:
January 16, 2018
Total Price:
$1.40
Designed to work with the MD-80SV
Designed to work with the MD-80SV
Sinclair - RC3 - Tented
author: ArduinoEnigma
2 layer board of 2.05 x 3.94 inches (52.0 x 100.0 mm)
Uploaded:
January 16, 2018
Shared:
January 16, 2018
Total Price:
$40.30
