Shared Projects

Enables use of 4 NES, NES, and/or N64 controllers as USB Joysticks

Replacement: https://oshpark.com/shared_projects/dC3iqMxp

EDIT, NOTE: PWM pins are hooked up backwards on v012, requires code changes in order to work right.

• added a covered 1mm via for SW+ hookup from rear, pass your wire through and just solder onto OTC pad if you want.
• improved LED- trace on bottom in order to facilitate the chunk eaten up by the 1mm via above.
• Increased LED+ and LED- vias to 1.3mm

BMX-055 9-axis motion sensor plus MS5637 pressure sensor with the SENtral EM7180 sensor fusion hub with M24512DFM EEPROM to store the SENtral configuration file. SENtral takes 9-axis accel/gyro/mag from BMX-055 and performs hardware sensor fusion returning raw data, quaternions, linear acceleration, and heading, etc. First attempt at using wafer-level, chip-scale package (WL-CSP). Breakout board using the SENtral with jumpers to take power from edge pins for breadboard use or to mount directly on the Teensy 3.1 for comparison between open-source software sensor fusion and the hardware sensor fusion provided by the SENtral.

Test board for ENC424J600

WR703N Expander v1

Developed in conjunction with the Sydney Hackerspace Robots and Dinosaurs Inc – June 2012 (featured on Hack A Day 24th June 2012)

This project is a small USB Hub & FTDI dual serial/GPIO/JTAG adapter. It was designed to match the form factor of the TP-LINK WR703N router, but can be used with almost any USB host. If you haven’t used the WR703N - it is a great little OpenWRT box, made even better with the I/O expansion from this board.

http://www.kean.com.au/oshw/WR703N/

http://wiki.openwrt.org/toh/tp-link/tl-wr703n

2 layer board of 1.93x2.01 inches (49x51mm). $19.30 for three.

USB led notifier

Now with less arcing and magic smoke release!

Uses a 10k resistor and Quad Analog Switch IC 4066 DIP14, schematic by Trimesh and following info:

Normally when you plug a cart in it grounds pin B32 of the cart connector - this is wired to the ASIC and when it’s grounded the TMSS ROM gets paged in. So if you just cut this line it disables TMSS - but it also disables the ROM CS/ line fed to the cartridge ROM, so the game won’t run. To get around this, ROM CS/ (pin B17) is disconnected from the ASIC and wired directly to A23 on the CPU address bus. This maps the ROM into the lower half of the CPU address space, At this point, the ASIC still doesn’t know the cart is plugged in, but the CPU can see valid instructions and will run the cart anyway.

This is obviously a very simple modification (2 trace cuts and one piece of wire), and it does effectively disable TMSS - but it also breaks compatibility with the various Mega Drive/Genesis addons. The 32X and the power base converter won’t work at all, and the Sega CD will work, but you can’t use cartridges when it’s plugged in (and in fact run the risk of damaging the cart, Sega CD or both through bus contention).

You can fix the 32X and PBC compatibility by checking the M3/ line (pin B30) - if it’s low, you have an accessory connected and you should renable CART IN/ and connect ROM CS/ back to the ASIC output pin. From a quick look at the schematic, this seems to be exactly what the mod in the first post is doing.

Personally, I would be inclined to use an analog switch chip to handle this, since it would be a lot simpler

Try this - note that it hasn’t been tested and might not work, but it looks reasonable, and it’s just a single chip..

no 12v, alim 5v on board, no gfci, no ac test

Build DOC https://drive.google.com/file/d/0B885rNIdD167R1hLc2s0aFB0UUk/view?usp=sharing

v0.13

Changed the main displays to have through-hole solder points.

H-bro utgang

Med transistorutganger

Original design by Mattaus. Beefed up traces and vias; added zener pad; and a few more tweaks.

• C1: 10uF 0603 Capacitor
• D1: SOD-323 Diode
• R1: 19.1k 0603 Resistor
• R2: 4.7k 0603 Resistor
• U1: attiny13a-SSH/SSU MCU
• AMC7135 Linear Regulating Chips
• Z: Optional SOD-323 4.3v Zener Diode (also replace D1 with 200 ohm 0805 resistor if this is populated)
• “3” and “4” correspond to MCU pins 3 and 2, respectively.

This driver works with any firmware with dual PWM output, such as STAR Dual-PWM by JonnyC; Pin 5 is connected to a single 7135 pad; Pin 6 is connected to 7 7135 pads.

Simple 16-bit ISA to pin header adapter. Can also supply -5V, if required.

Christmas Tree Shaped LED Arduino

New non-Zener / LDO version. Do not become confused and order this instead of A17DD-SO8

ProMini clock shield with dual (8 digit) bubble display.

More details here

Rev1.1