LMX9838
author: will3509111
2 layer board of 0.71 x 1.01 inches (18.0 x 25.6 mm)
Uploaded:
August 26, 2014
Shared:
October 03, 2014
Total Price:
$3.55
Big Purple Driver, Rev. 4
author: msds
2 layer board of 1.80 x 1.60 inches (45.7 x 40.6 mm)
Uploaded:
October 03, 2014
Shared:
October 03, 2014
Total Price:
$14.40
See https://oshpark.com/shared_projects/X2GXvqlH for details - v4 just adds a header for convenient access to motor voltage.
See https://oshpark.com/shared_projects/X2GXvqlH for details - v4 just adds a header for convenient access to motor voltage.
IF-A386
author: mhectorgato
2 layer board of 0.84 x 1.10 inches (21.3 x 27.9 mm)
Uploaded:
September 29, 2014
Shared:
October 02, 2014
Total Price:
$4.60
theIronForgeOrlando.com - Amplifier based on LM386
theIronForgeOrlando.com - Amplifier based on LM386
Electret Microphone Preamp
author: mhectorgato
2 layer board of 0.93 x 0.30 inches (23.5 x 7.6 mm)
Uploaded:
September 09, 2014
Shared:
October 02, 2014
Total Price:
$1.35
Electret Microphone Preamp
Electret Microphone Preamp
Tiniest10
author: Mattaus
2 layer board of 0.40 x 0.40 inches (10.3 x 10.3 mm)
Uploaded:
May 02, 2014
Shared:
October 01, 2014
Total Price:
$0.80
FET1: IRLML2502 , SOT-23
Q2: 2DD2656-7, SOT323
R: 0402, 200ohm
RSet: 1206 , 220 - 470ohm
MCU: PIC10F322 (NOT LF), I/OT
C: 0402, 10uF
D: BAS70KFILM, SOD-523
FET1: IRLML2502 , SOT-23
Q2: 2DD2656-7, SOT323
R: 0402, 200ohm
RSet: 1206 , 220 - 470ohm
MCU: PIC10F322 (NOT LF), I/OT
C: 0402, 10uF
D: BAS70KFILM, SOD-523
usb headphones amp
author: 00940
2 layer board of 1.97 x 1.97 inches (50.0 x 50.0 mm)
Uploaded:
October 01, 2014
Shared:
October 01, 2014
Total Price:
$19.35
see: http://www.diyaudio.com/forums/headphone-systems/261952-opa2134-lm6172-composite-amp.html
see: http://www.diyaudio.com/forums/headphone-systems/261952-opa2134-lm6172-composite-amp.html
Tinusaur Board v0.2 RC4
author: boyanov
2 layer board of 0.90 x 1.40 inches (23.0 x 35.7 mm)
Uploaded:
October 01, 2014
Shared:
October 01, 2014
Total Price:
$6.30
The Tinusaur - a minimal micro-controller hardware configuration based on Atmel AVR ATtiny85
The Tinusaur - a minimal micro-controller hardware configuration based on Atmel AVR ATtiny85
ZeroGeckoProto (ZGP)
author: whiskthecat
2 layer board of 1.02 x 0.55 inches (26.0 x 14.0 mm)
Uploaded:
October 01, 2014
Shared:
October 01, 2014
Total Price:
$2.80
Minimal DIP for QFN24 Gecko
Minimal DIP for QFN24 Gecko
PLL Wing
author: DiegoRosales
2 layer board of 0.81 x 0.85 inches (20.6 x 21.6 mm)
Uploaded:
September 30, 2014
Shared:
September 30, 2014
Total Price:
$3.45
PLL Wing using the PLL1705
PLL Wing using the PLL1705
Open Sauce Charger r1.1
author: LightningStalker
2 layer board of 0.69 x 0.64 inches (17.4 x 16.4 mm)
Uploaded:
September 30, 2014
Shared:
September 30, 2014
Total Price:
$2.20
10440 Battery Charger using the MCP73831/2
10440 Battery Charger using the MCP73831/2
ATTiny10 Breakout Board
author: Blueberry
2 layer board of 0.65 x 0.55 inches (16.5 x 14.0 mm)
Uploaded:
September 30, 2014
Shared:
September 30, 2014
Total Price:
$1.75
A breakout board for an ATTiny10. The controller and filter cap are mounted on the bottom, and the pins are labelled on the top.
Just add an ATTiny10, a 0.1uF cap in a 0805 package, and a 6 pin header (0.100" pitch).
This board may be appropriate for other six pin variants of this m…
Show full description
A breakout board for an ATTiny10. The controller and filter cap are mounted on the bottom, and the pins are labelled on the top.
Just add an ATTiny10, a 0.1uF cap in a 0805 package, and a 6 pin header (0.100" pitch).
This board may be appropriate for other six pin variants of this m…
Show full description
