AMETEK_PD2_POWERBOARD_REV2
author: UNCCAustinGeorge
2 layer board of 3.40 x 4.60 inches (86.4 x 116.9 mm)
Uploaded:
March 29, 2021
Shared:
March 29, 2021
Total Price:
$78.30
Second revision to the AMETEK_PD2 power board.
Second revision to the AMETEK_PD2 power board.
FOBOS 3 Shield Z1 rev2.0
author: jpkaps
4 layer board of 3.01 x 2.81 inches (76.4 x 71.3 mm)
Uploaded:
March 16, 2021
Shared:
March 29, 2021
Total Price:
$84.30
PYNQ-Z1 Shield for FOBOS 3, revision 2.0
Information about this board is available at the FOBOS Homepage. The board schematic, layout, bill-of-material, etc. is available in our git project at GitHub.
PYNQ-Z1 Shield for FOBOS 3, revision 2.0
Information about this board is available at the FOBOS Homepage. The board schematic, layout, bill-of-material, etc. is available in our git project at GitHub.
Filter adapter, hand-solder pads
author: DavidPlatt
2 layer board of 0.42 x 0.46 inches (10.7 x 11.6 mm)
Uploaded:
March 28, 2021
Shared:
March 29, 2021
Total Price:
$0.95
Through-hole adapter for Murata 10.7 MHz IF filters. Over-sized pads for easier hand soldering.
Through-hole adapter for Murata 10.7 MHz IF filters. Over-sized pads for easier hand soldering.
dongle-re-smd.kicad_pcb
author: Cybersmythe
2 layer board of 2.64 x 3.04 inches (67.1 x 77.1 mm)
Uploaded:
October 19, 2020
Shared:
March 27, 2021
Total Price:
$40.10
A surface mount keyer dongle that uses a rotary encoder for speed and configuration control. The source for the firmware is on Github
The hardware design (including schematic, gerbers, and bill of materials) is also on [Github](https://github.com/K…
Show full description
A surface mount keyer dongle that uses a rotary encoder for speed and configuration control. The source for the firmware is on Github
The hardware design (including schematic, gerbers, and bill of materials) is also on [Github](https://github.com/K…
Show full description
Mac Rom-inator
author: colinng
2 layer board of 1.97 x 1.97 inches (50.1 x 50.1 mm)
Uploaded:
October 28, 2020
Shared:
March 27, 2021
Total Price:
$19.40
Mac Rom-inator from https://www.bigmessowires.com/mac-rom-inator/
Mac Rom-inator from https://www.bigmessowires.com/mac-rom-inator/
Lume X1 - KR1 - TriLED PCB - Rev A
author: loneoceanslabs
2 layer board of 0.81 x 0.81 inches (20.5 x 20.5 mm)
Uploaded:
January 04, 2021
Shared:
March 27, 2021
Total Price:
$3.25
Auxiliary Tri-LED Board for KR1, designed for use with 7070 LEDs like the XHP70.2 or GT-FC40 or similar; designed for use with the Lume X1 LED driver. 20.45mm diameter, similar to Noctigon MCPCBs.
Recommended 0.8mm PCB thickness, 0402 resistors, 0402 LEDs. NOTE - G2 LED was rotated 180deg by e…
Show full description
Auxiliary Tri-LED Board for KR1, designed for use with 7070 LEDs like the XHP70.2 or GT-FC40 or similar; designed for use with the Lume X1 LED driver. 20.45mm diameter, similar to Noctigon MCPCBs.
Recommended 0.8mm PCB thickness, 0402 resistors, 0402 LEDs. NOTE - G2 LED was rotated 180deg by e…
Show full description
QuadADC v3
author: evgeny.redekop
4 layer board of 6.30 x 3.94 inches (160.1 x 100.1 mm)
Uploaded:
March 25, 2021
Shared:
March 25, 2021
Total Price:
$248.20
Cinesense
author: jaytavares
2 layer board of 1.46 x 0.58 inches (37.1 x 14.8 mm)
Uploaded:
March 25, 2021
Shared:
March 25, 2021
Total Price:
$4.25
See the Github project page for the BOM and the software. Use this board to add automatic audio signal sensing to your Bose Cinemate Series II speakers.
See the Github project page for the BOM and the software. Use this board to add automatic audio signal sensing to your Bose Cinemate Series II speakers.
