afromini hex brushed esc
author: KoekieMonster
2 layer board of 0.61 x 0.48 inches (15.6 x 12.1 mm)
Uploaded:
February 07, 2015
Shared:
February 07, 2015
Total Price:
$1.45
afromini hex brushed esc
ONLY WORKS WITH REV 0 or REV 1. NOT WITH REV 3. if you need this for revision 3 please send a PM to KoekieMonster @ rcgroups.com, then I'll draw it.
afromini hex brushed esc
ONLY WORKS WITH REV 0 or REV 1. NOT WITH REV 3. if you need this for revision 3 please send a PM to KoekieMonster @ rcgroups.com, then I'll draw it.
serial-isolator
author: Kingswood
2 layer board of 0.80 x 0.40 inches (20.3 x 10.2 mm)
Uploaded:
February 07, 2015
Shared:
February 07, 2015
Total Price:
$1.60
High speed optocoupler isolator for 3V serial port.
Optocoupler is Avago ACPL-M21L SO5, resistors 470R, capacitors 100n.
High speed optocoupler isolator for 3V serial port.
Optocoupler is Avago ACPL-M21L SO5, resistors 470R, capacitors 100n.
RYO_TC2050-ARM2010
author: igrokspock
2 layer board of 1.22 x 0.68 inches (31.0 x 17.2 mm)
Uploaded:
February 07, 2015
Shared:
February 07, 2015
Total Price:
$4.10
"Roll your own" Tag-Connect ARM2010 SAMICE Adapter…
"Roll your own" Tag-Connect ARM2010 SAMICE Adapter…
Zero Tiny BLE V2.0
author: micahpearlman
2 layer board of 0.79 x 1.85 inches (20.0 x 47.0 mm)
Uploaded:
February 02, 2015
Shared:
February 06, 2015
Total Price:
$7.25
First production run of Zero Tiny BLE
First production run of Zero Tiny BLE
AJQuick 4-Axis CNC Controller Board
author: IOTLLC
2 layer board of 7.20 x 2.20 inches (182.9 x 55.9 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$79.20
CNC Controller is a Unipolar Stepper motor controller based on the SLA7078MPR by Allegro Microsystems
CNC Controller is a Unipolar Stepper motor controller based on the SLA7078MPR by Allegro Microsystems
Cat Laser Control Board
author: stuthedew
2 layer board of 1.70 x 1.70 inches (43.2 x 43.2 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$14.40
See https://github.com/stuthedew/Arduino-Laser-Cat-Turret
See https://github.com/stuthedew/Arduino-Laser-Cat-Turret
Raspberry Pi Hub75-Dual v1.1
author: CaptainMurdoch
2 layer board of 1.44 x 1.00 inches (36.5 x 25.4 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$7.15
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a set of HUB75 compatible LED panel into the GPIO header on…
Show full description
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a set of HUB75 compatible LED panel into the GPIO header on…
Show full description
Raspberry Pi Hub75 v1.1
author: CaptainMurdoch
2 layer board of 1.44 x 0.65 inches (36.5 x 16.5 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$4.65
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a HUB75 compatible LED panel into the GPIO header on a Rasp…
Show full description
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a HUB75 compatible LED panel into the GPIO header on a Rasp…
Show full description
Icetube Clock - Transistor - Rev C
author: PhilD13
2 layer board of 4.50 x 1.08 inches (114.4 x 27.4 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$24.25
A version of the Adafruit Icetube clock main board that will accept either a ZVP2110A FET (use a jumper wire for R6) or a PN2907 transistor for Q3 and use 470 ohm (min value) - 1K ohm (max value) for resistor R6. Suggest using firmware found here for the clock. https://github.com/johngarchie/xm…
Show full description
A version of the Adafruit Icetube clock main board that will accept either a ZVP2110A FET (use a jumper wire for R6) or a PN2907 transistor for Q3 and use 470 ohm (min value) - 1K ohm (max value) for resistor R6. Suggest using firmware found here for the clock. https://github.com/johngarchie/xm…
Show full description
Alps EC11K15 breadboard helper v1.1
author: djm
2 layer board of 1.20 x 1.00 inches (30.5 x 25.4 mm)
Uploaded:
December 01, 2014
Shared:
February 06, 2015
Total Price:
$6.00
A breadboard adapter for an Alps EC11K15 rotary encoder that includes pullup resistors and debouncing caps. Connector pins ensure the helper board sits firmly on the breadboard beneath.
A breadboard adapter for an Alps EC11K15 rotary encoder that includes pullup resistors and debouncing caps. Connector pins ensure the helper board sits firmly on the breadboard beneath.
X360 Power Adapter
author: Element18592
2 layer board of 3.80 x 1.56 inches (96.5 x 39.7 mm)
Uploaded:
February 04, 2015
Shared:
February 06, 2015
Total Price:
$29.65
A Molex and USB adapter powered by the Xbox 360 Phat PSU.
A Molex and USB adapter powered by the Xbox 360 Phat PSU.
