PressureSensorTestBoard.v01
author: PeskyProducts
2 layer board of 0.71 x 0.51 inches (17.9 x 12.8 mm)
Uploaded:
March 01, 2015
Shared:
March 01, 2015
Total Price:
$1.75
Simple Teensy 3.1 add-on board to test the relative performance of various state-of-the-art MEMS pressure sensors. Included is Invensense's 3.5 mm x 3.5 mm ICM20730 7-axis motion sensor with accel/gyro and embedded pressure sensor, Bosch's 2.5 mm x 2 mm BMP280, ST Microelectronics' 2.5 mm x 2.5 m…
Show full description
Simple Teensy 3.1 add-on board to test the relative performance of various state-of-the-art MEMS pressure sensors. Included is Invensense's 3.5 mm x 3.5 mm ICM20730 7-axis motion sensor with accel/gyro and embedded pressure sensor, Bosch's 2.5 mm x 2 mm BMP280, ST Microelectronics' 2.5 mm x 2.5 m…
Show full description
KombyPiMini
author: Materdaddy
2 layer board of 2.49 x 0.85 inches (63.2 x 21.6 mm)
Uploaded:
December 29, 2014
Shared:
March 01, 2015
Total Price:
$10.55
Minimalist Shield for nRF on a Pi
Minimalist Shield for nRF on a Pi
INMP441.I2SDigitalMicrophone.v04x
author: PeskyProducts
2 layer board of 0.31 x 0.41 inches (7.8 x 10.3 mm)
Uploaded:
February 28, 2015
Shared:
February 28, 2015
Total Price:
$0.60
Invensense’s bottom-ported MEMS digital microphone with an embedded ASIC which directly outputs 24-bit I2S serial data without the need of a CODEC. Board is intended as a standalone microphone for breadboarding.
Invensense’s bottom-ported MEMS digital microphone with an embedded ASIC which directly outputs 24-bit I2S serial data without the need of a CODEC. Board is intended as a standalone microphone for breadboarding.
TCPoke
author: WishfulCoding
2 layer board of 1.00 x 0.80 inches (25.5 x 20.4 mm)
Uploaded:
February 28, 2015
Shared:
February 28, 2015
Total Price:
$4.00
Internet of Pokemon
Internet of Pokemon
Raspberry Pi HUB75-Backpack v1.0
author: CaptainMurdoch
2 layer board of 1.39 x 0.60 inches (35.3 x 15.3 mm)
Uploaded:
February 13, 2015
Shared:
February 28, 2015
Total Price:
$4.15
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a Raspberry Pi into a HUB75 compatible LED panel. The 26-pi…
Show full description
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a Raspberry Pi into a HUB75 compatible LED panel. The 26-pi…
Show full description
Simon kit PCB
author: loans
2 layer board of 1.59 x 1.71 inches (40.4 x 43.4 mm)
Uploaded:
February 28, 2015
Shared:
February 28, 2015
Total Price:
$13.55
Soldering kit that is an implementation of the game Simon
See: the Github page.
Soldering kit that is an implementation of the game Simon
See: the Github page.
TLV3011 based protection board
author: sir066
2 layer board of 0.79 x 0.40 inches (20.0 x 10.2 mm)
Uploaded:
February 01, 2015
Shared:
February 27, 2015
Total Price:
$1.55
TLV3011 based supercapacitor overvoltage protection board (rev 0.2)
TLV3011 based supercapacitor overvoltage protection board (rev 0.2)
CameraFlash.v01
author: PeskyProducts
2 layer board of 0.25 x 0.25 inches (6.4 x 6.4 mm)
Uploaded:
February 27, 2015
Shared:
February 27, 2015
Total Price:
$0.30
Simple breakout test board for Philips Luxeon Z ES LXZ2-4080 ultra-high luminance LED for camera flash application.
Simple breakout test board for Philips Luxeon Z ES LXZ2-4080 ultra-high luminance LED for camera flash application.
Generic LVD
author: austindavid
2 layer board of 1.65 x 1.50 inches (41.9 x 38.1 mm)
Uploaded:
February 27, 2015
Shared:
February 27, 2015
Total Price:
$12.35
Low Voltage Disconnect w/ MOSFET
Low Voltage Disconnect w/ MOSFET
RobotaE
author: ModernDevice
2 layer board of 5.16 x 2.66 inches (131.0 x 67.5 mm)
Uploaded:
February 04, 2015
Shared:
February 26, 2015
Total Price:
$68.50
RobotaE
RobotaE
