0.91" OLED breakout
author: doobedoobedo
2 layer board of 0.73 x 1.42 inches (18.6 x 36.1 mm)
Uploaded:
January 07, 2016
Shared:
January 25, 2016
Total Price:
$5.20
For SSD1306 128x32 OLED with 15 pin zif connector
BOM
C1: 1uf
C2: 1uf
C3: 0.1uf
C4: 4.7uf
C5: 0.1uf
C6: 4.7uf
C7: 2.2uf
R1: 560K
ZIF connector: Hirose FH19C-15S-0.5SH
For SSD1306 128x32 OLED with 15 pin zif connector
BOM
C1: 1uf
C2: 1uf
C3: 0.1uf
C4: 4.7uf
C5: 0.1uf
C6: 4.7uf
C7: 2.2uf
R1: 560K
ZIF connector: Hirose FH19C-15S-0.5SH
MCP9802 Temperature Sensor
author: K8VFO
2 layer board of 0.68 x 0.51 inches (17.2 x 12.8 mm)
Uploaded:
January 25, 2016
Shared:
January 25, 2016
Total Price:
$1.70
MCP9802 Temperature Sensor for use on High Altitude Balloon
MCP9802 Temperature Sensor for use on High Altitude Balloon
TSOP32 to DIL28 adapter
author: system11
2 layer board of 0.73 x 1.43 inches (18.6 x 36.3 mm)
Uploaded:
January 25, 2016
Shared:
January 25, 2016
Total Price:
$5.20
To make chip-sized replacements for 28 pin MASK ROMs, program chip before fitting.
To make chip-sized replacements for 28 pin MASK ROMs, program chip before fitting.
ChimPWM - MonkeyTokes Tiny
author: BananaGuns
2 layer board of 0.95 x 0.53 inches (24.2 x 13.4 mm)
Uploaded:
January 07, 2016
Shared:
January 25, 2016
Total Price:
$2.50
Combination of my Tiny PWM and MonkeyTokes PCBs for a slightly smaller DIP-8 based, dual mosfet, 555 PWM PCB
Combination of my Tiny PWM and MonkeyTokes PCBs for a slightly smaller DIP-8 based, dual mosfet, 555 PWM PCB
Battery Charger 6-Ports Li-Ion
author: BenjaminG
2 layer board of 3.00 x 1.00 inches (76.2 x 25.4 mm)
Uploaded:
December 30, 2015
Shared:
January 25, 2016
Total Price:
$15.00
- Uses NXP MC34671 li-ion charging IC.
- Power with micro-usb. Intended to be low current battery charger <300ma per channel. I have one of these set up to charge at 100ma.
- The USB-micro socket is all SMD. Added vias to the pads for strength but should have used type with through-hole tabs…
Show full description
- Uses NXP MC34671 li-ion charging IC.
- Power with micro-usb. Intended to be low current battery charger <300ma per channel. I have one of these set up to charge at 100ma.
- The USB-micro socket is all SMD. Added vias to the pads for strength but should have used type with through-hole tabs…
Show full description
Courui D01 V3
author: mattlward
2 layer board of 1.59 x 1.59 inches (40.3 x 40.3 mm)
Uploaded:
January 25, 2016
Shared:
January 25, 2016
Total Price:
$12.55
This will allow any standard driver to be top mounted. Center via 12 awg, for support of the driver. LED+ vias are for 18 awg wire direct to LED. Top ground contacts are for 3.0mm copper strip from Hobby Lobby. Hand fitting will be required!
[BLF thread](http://budgetlightforum.com/node/44403#…
Show full description
This will allow any standard driver to be top mounted. Center via 12 awg, for support of the driver. LED+ vias are for 18 awg wire direct to LED. Top ground contacts are for 3.0mm copper strip from Hobby Lobby. Hand fitting will be required!
[BLF thread](http://budgetlightforum.com/node/44403#…
Show full description
LEDBlinker-00-00
author: dijonx
2 layer board of 1.06 x 1.06 inches (26.8 x 26.8 mm)
Uploaded:
January 24, 2016
Shared:
January 24, 2016
Total Price:
$5.55
blinks some LEDs - order hardware kit at engenuics.com to go with this
blinks some LEDs - order hardware kit at engenuics.com to go with this
Lux Lighting - Flasher Rev1
author: TonyBurroughs
2 layer board of 1.35 x 0.57 inches (34.2 x 14.4 mm)
Uploaded:
January 24, 2016
Shared:
January 24, 2016
Total Price:
$3.80
Lux Lighting - Flasher Rev1
Lux Lighting - Flasher Rev1
Prop
author: bloguetronica
4 layer board of 1.30 x 2.10 inches (33.0 x 53.4 mm)
Uploaded:
December 04, 2015
Shared:
January 24, 2016
Total Price:
$27.30
P8X32A development board
P8X32A development board
Snowboard/ski mounted GPS/G-force logger
author: GijsvanBerne
2 layer board of 1.97 x 1.97 inches (50.0 x 50.0 mm)
Uploaded:
January 23, 2016
Shared:
January 23, 2016
Total Price:
$19.35
Dedicated ski or snowboard mounted journey logger with g-force/orientation data + display (speed, max-speed, min-max altitude, g-force acceleration etc).
GPS MTK3339; 3-Axis Accelerometer MMA8452Q; Micro SD-card logger; OLED 0.96 display module; Efficient TPS63031 3V3 Buck Boost converter; MCP…
Show full description
Dedicated ski or snowboard mounted journey logger with g-force/orientation data + display (speed, max-speed, min-max altitude, g-force acceleration etc).
GPS MTK3339; 3-Axis Accelerometer MMA8452Q; Micro SD-card logger; OLED 0.96 display module; Efficient TPS63031 3V3 Buck Boost converter; MCP…
Show full description
PD68 Lighted Switch -16mm Rev5 Bottom
author: pilotdog68
2 layer board of 0.63 x 0.63 inches (15.9 x 15.9 mm)
Uploaded:
January 23, 2016
Shared:
January 23, 2016
Total Price:
$1.95
2x4_pinhead_breakout_DIP_turned.brd
author: flopp
2 layer board of 0.49 x 0.50 inches (12.4 x 12.7 mm)
Uploaded:
January 23, 2016
Shared:
January 23, 2016
Total Price:
$1.20
Breakout for 2x4 pin head to DIP turned so it doesn't block the connections on a breadboard. e.g. if not turned a ESP-01 or nRF24L01+ will block connections under itself
Breakout for 2x4 pin head to DIP turned so it doesn't block the connections on a breadboard. e.g. if not turned a ESP-01 or nRF24L01+ will block connections under itself
