TEST: copy of CHIP_motor_shield
author: fustini
2 layer board of 1.63 x 1.99 inches (41.4 x 50.4 mm)
Uploaded:
February 11, 2016
Shared:
February 11, 2016
Total Price:
$16.15
TEST: copy of CHIP_motor_shield by KoljaWindeler https://github.com/KoljaWindeler/CHIP_motor_shield
TEST: copy of CHIP_motor_shield by KoljaWindeler https://github.com/KoljaWindeler/CHIP_motor_shield
BlueSaab v3.3
author: Edison517
2 layer board of 2.36 x 2.44 inches (60.0 x 62.0 mm)
Uploaded:
February 11, 2016
Shared:
February 11, 2016
Total Price:
$28.75
Added additional bottom silk screen labels to RN52. MINOR tweak to BT1 and BT2 vias. Added Hardware Rev resistor R13 with R14 (resistor divider network) for possible future use. Added R15 & C10 for outputting pwm power signal to PWREN pin on RN52. Added SMD jumper to short GPIO7 to ground to forc…
Show full description
Added additional bottom silk screen labels to RN52. MINOR tweak to BT1 and BT2 vias. Added Hardware Rev resistor R13 with R14 (resistor divider network) for possible future use. Added R15 & C10 for outputting pwm power signal to PWREN pin on RN52. Added SMD jumper to short GPIO7 to ground to forc…
Show full description
TEST: copy of CHIP_pwm_shield
author: fustini
2 layer board of 1.63 x 1.99 inches (41.4 x 50.4 mm)
Uploaded:
February 11, 2016
Shared:
February 11, 2016
Total Price:
$16.15
TEST: I uploaded CHIP_pwm_shield by KoljaWindeler. simple PWM, mosfet shield to drive led strips with the C.H.I.P. GitHub: https://github.com/KoljaWindeler/CHIP_pwm_shield Forum: https://bbs.nextthing.co/t/salsa-dip-for-c-h-i-p-i2c-arduino-ws2812-pwm-motor/1597/70
TEST: I uploaded CHIP_pwm_shield by KoljaWindeler. simple PWM, mosfet shield to drive led strips with the C.H.I.P. GitHub: https://github.com/KoljaWindeler/CHIP_pwm_shield Forum: https://bbs.nextthing.co/t/salsa-dip-for-c-h-i-p-i2c-arduino-ws2812-pwm-motor/1597/70
IGBT Bridge V1
author: Extreme-Electronics
2 layer board of 2.39 x 2.38 inches (60.7 x 60.3 mm)
Uploaded:
January 18, 2016
Shared:
February 11, 2016
Total Price:
$28.35
IGBT Bridge V1 Cockup - Two transistors have heat sink mount in the middle of the board. more details at extelec.uk/brg
IGBT Bridge V1 Cockup - Two transistors have heat sink mount in the middle of the board. more details at extelec.uk/brg
Arduino UNO - HC-06 Mini Shield
author: MatsK
2 layer board of 2.07 x 0.92 inches (52.6 x 23.4 mm)
Uploaded:
January 17, 2016
Shared:
February 10, 2016
Total Price:
$9.50
Arduino UNO - HC-06 Mini Shield <https://github.com/MatsK/Arduino-Mini-Shield>
Arduino UNO - HC-06 Mini Shield <https://github.com/MatsK/Arduino-Mini-Shield>
Lin_Sen_mount.brd
author: anilinfotek
2 layer board of 2.54 x 0.51 inches (64.5 x 13.0 mm)
Uploaded:
February 10, 2016
Shared:
February 10, 2016
Total Price:
$6.50
Mot_Drv_Int.brd
author: anilinfotek
2 layer board of 1.99 x 2.10 inches (50.4 x 53.4 mm)
Uploaded:
February 10, 2016
Shared:
February 10, 2016
Total Price:
$20.85
Rx5808 fpv receiver V1.1
author: spikey
2 layer board of 1.59 x 1.50 inches (40.3 x 38.1 mm)
Uploaded:
December 13, 2015
Shared:
February 10, 2016
Total Price:
$11.90
Same as previous, just a bit smaller. FPV receiver, based on rx5808 PRO.
unmodded rx5808 from ebay
Modded rx5805 Module is …
Show full description
Same as previous, just a bit smaller. FPV receiver, based on rx5808 PRO.
unmodded rx5808 from ebay
Modded rx5805 Module is …
Show full description
stm32-tiny042-v2
author: dword1511
2 layer board of 0.94 x 0.62 inches (23.9 x 15.8 mm)
Uploaded:
January 21, 2016
Shared:
February 10, 2016
Total Price:
$2.90
Tiny STM32F042 USB board version 2, with PA0-PA7, PF0 & PF1 broken out and dual LEDs. Uses LP5907 LDO or other LDOs that has NC on BP pin.
Tiny STM32F042 USB board version 2, with PA0-PA7, PF0 & PF1 broken out and dual LEDs. Uses LP5907 LDO or other LDOs that has NC on BP pin.
