Shared Projects

Embeddable link to order this shared Project

IRArray.v01

author: PeskyProducts

2 layer board of 0.56 x 0.41 inches (14.2 x 10.3 mm)
Uploaded: October 07, 2016
Shared: October 07, 2016
Total Price: $1.10

Breakout for Melexis MLX90621 16 x 4 IR imaging array with 120 x 25 degrees FoV and maximum temperature range up to 750 C.

Embeddable link to order this shared Project

sharpbreak_rev0.01

author: 1rel

2 layer board of 1.57 x 0.94 inches (39.9 x 23.8 mm)
Uploaded: October 07, 2016
Shared: October 07, 2016
Total Price: $7.35

Embeddable link to order this shared Project

kyobreak_rev0.01

author: 1rel

2 layer board of 1.64 x 0.64 inches (41.7 x 16.2 mm)
Uploaded: October 07, 2016
Shared: October 07, 2016
Total Price: $5.20

Embeddable link to order this shared Project

reDOT

author: ALKR

2 layer board of 0.39 x 0.73 inches (9.8 x 18.4 mm)
Uploaded: September 22, 2016
Shared: October 06, 2016
Total Price: $1.40

TIL305 remake with 0402 SMD LEDs. more Information: https://hackaday.io/project/15102

Embeddable link to order this shared Project

ethernet_breakout_ab_2.brd

author: abagaria

2 layer board of 1.41 x 0.90 inches (35.9 x 22.9 mm)
Uploaded: August 23, 2016
Shared: October 06, 2016
Total Price: $6.35

Ethernet Breakout Board for E79

Embeddable link to order this shared Project

Minifigure SAMD21 Board

author: bwshockley

4 layer board of 0.96 x 1.53 inches (24.3 x 38.8 mm)
Uploaded: October 06, 2016
Shared: October 06, 2016
Total Price: $14.50

Minifigure-SAMD21E

SAMD21E based Minifigure shaped development board.

Github

About

This circuit board was designed as a fun project for a SAMD21E microcontroller based development board. The c…

Minifigure-SAMD21E

SAMD21E based Minifigure shaped development board.

Github

About

This circuit board was designed as a fun project for a SAMD21E microcontroller based development board. The circuit design follows the recommended design from the SAMD Datasheet - including section 39. Schematic Checklist. The USB protection may be overkill, but it is complete. I made this just for fun - I am not going to provide any special support, but always welcome recommendations, suggestions, and ideas for improvements. You are free to take it and run with it, but do not sell this design.

Etc

I have not yet tested the design. As it sits, it should pass DRC for OSHPark manufacture with two major unknowns. 1) Wether or not the cutouts for the hands will be manufactured as intended and 2) The exact outline of the board - there may be some corners, nooks, and crannies that are not manufactured by OSHPark and will require additional filing/work by me. I will update once I get a set manufactured.

BOM

The schematic has all items listed and values and should be easily sourced. Additionally, I have setup a project on mouser.com that can be found here. The BOM through mouser is roughly 12 USD at this time (Oct 2016). It does not include the WS8212B 3535 LED - these can be sourced from Adafruit or eBay among others. The LED does not need to be populated for the board to function, but it is fun.

Firmware

I plan on trying to implement both Arduino and possibly Micropython on this board, but need some significant help with this. I will update as I can.

License

For personal use only - do not sell. You may modify as you wish.

Show full description

Minifigure-SAMD21E

SAMD21E based Minifigure shaped development board.

Github

About

This circuit board was designed as a fun project for a SAMD21E microcontroller based development board. The c…

Minifigure-SAMD21E

SAMD21E based Minifigure shaped development board.

Github

About

Etc

BOM

Firmware

I plan on trying to implement both Arduino and possibly Micropython on this board, but need some significant help with this. I will update as I can.

License

For personal use only - do not sell. You may modify as you wish.

Show full description

Embeddable link to order this shared Project

BBBMini

author: emolson

2 layer board of 3.40 x 2.15 inches (86.5 x 54.7 mm)
Uploaded: October 06, 2016
Shared: October 06, 2016
Total Price: $36.65

BBBMini BeagleBone Linux ArduPilot DIY Cape

Embeddable link to order this shared Project

joystick panel 12HP

author: EATyourGUITAR

2 layer board of 2.39 x 5.06 inches (60.6 x 128.5 mm)
Uploaded: September 06, 2016
Shared: October 06, 2016
Total Price: $60.35

eurorack 12HP analog joystick

Embeddable link to order this shared Project

ARP-3620.zip

author: dingebre

2 layer board of 6.31 x 8.67 inches (160.2 x 220.1 mm)
Uploaded: September 16, 2016
Shared: October 06, 2016
Total Price: $273.20

PCB for ARP 3620 keyboard clone. See MuffWiggler forum for details. https://www.muffwiggler.com/forum/viewtopic.php?t=118486&highlight=

Embeddable link to order this shared Project

OpticSpy Digital (Rev. A)

author: joegrand

2 layer board of 1.37 x 1.68 inches (34.8 x 42.6 mm)
Uploaded: October 01, 2016
Shared: October 05, 2016
Total Price: $11.45

Receiver module for Optical Covert Channel experiments.

Digital version using Everlight PLR135/T9 Fiber Optic Receiver.

Receiver module for Optical Covert Channel experiments.

Digital version using Everlight PLR135/T9 Fiber Optic Receiver.

Embeddable link to order this shared Project

Dangerous 18mA 3V3 supply

author: Tomek

2 layer board of 2.10 x 0.47 inches (53.3 x 11.9 mm)
Uploaded: February 06, 2015
Shared: October 05, 2016
Total Price: $4.90

Do I know what I'm doing??

Embeddable link to order this shared Project

micro CC3D

author: Vladisenko

Project on GitHub pcb on frame

2 layer board of 1.17 x 0.76 inches (29.7 x 19.4 mm)
Uploaded: October 05, 2016
Shared: October 05, 2016
Total Price: $4.45

Brushed CC3D with FlySky receiver. v0.2.

Brushed CC3D with FlySky receiver. v0.2.

Project on GitHub pcb on frame

Embeddable link to order this shared Project

PiAQ HAT

author: CRTLabs

2 layer board of 2.56 x 2.23 inches (65.0 x 56.5 mm)
Uploaded: September 19, 2016
Shared: October 05, 2016
Total Price: $28.45

V0.1

Embeddable link to order this shared Project

TPA3106D1-V2

author: Khne

2 layer board of 1.58 x 1.11 inches (40.2 x 28.3 mm)
Uploaded: October 05, 2016
Shared: October 05, 2016
Total Price: $8.75

40W class D audio amp (24V DC)

Embeddable link to order this shared Project

Swedish Vaper 555 PWM v1.5.2 RPP (reverse polarity protection)

author: SwedishVaper

2 layer board of 0.41 x 0.66 inches (10.3 x 16.7 mm)
Uploaded: October 05, 2016
Shared: October 05, 2016
Total Price: $1.30

TESTED AND WORKING

(Support will only be offered on projects marked "TESTED AND WORKING", and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with Reverse Polarity P…

TESTED AND WORKING

(Support will only be offered on projects marked “TESTED AND WORKING”, and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with Reverse Polarity Protection, courtesy of a P-channel Mosfet.

This is NOT a buffered circuit, so recommended max input voltage is 12.6V (3S), but I have tested it up to 14V and although it worked, it may severely limit the life of the device. Only use higher than 12.6V at your own risk.

Recommended potentiometer value: 10K - 50K

Parts list:

1 x 0603 1K resistor

1 x 0603 0.1uF capacitor

1 x 0603 0.01uF capacitor

1 x SOT23 p-channel mosfet

1 x BAT54S dual diode (SOT23 package)

1 x SOIC-8 555 timer IC

1 x 3-pin through hole potentiometer, 10K to 50K recommended

Show full description

TESTED AND WORKING

(Support will only be offered on projects marked "TESTED AND WORKING", and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with Reverse Polarity P…

TESTED AND WORKING

(Support will only be offered on projects marked “TESTED AND WORKING”, and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with Reverse Polarity Protection, courtesy of a P-channel Mosfet.

Recommended potentiometer value: 10K - 50K

Parts list:

1 x 0603 1K resistor

1 x 0603 0.1uF capacitor

1 x 0603 0.01uF capacitor

1 x SOT23 p-channel mosfet

1 x BAT54S dual diode (SOT23 package)

1 x SOIC-8 555 timer IC

1 x 3-pin through hole potentiometer, 10K to 50K recommended

Show full description

Embeddable link to order this shared Project

Swedish Vaper 555 PWM v1.5c

author: SwedishVaper

2 layer board of 0.41 x 0.61 inches (10.3 x 15.4 mm)
Uploaded: October 05, 2016
Shared: October 05, 2016
Total Price: $1.20

TESTED AND WORKING

(Support will only be offered on projects marked "TESTED AND WORKING", and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with NO reverse polarit…

TESTED AND WORKING

(Support will only be offered on projects marked “TESTED AND WORKING”, and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with NO reverse polarity protection.

Recommended potentiometer value: 10K - 50K

Parts list:

1 x 0603 1K resistor

1 x 0603 0.1uF capacitor

1 x 0603 0.01uF capacitor

1 x BAT54S dual diode (SOT23 package)

1 x SOIC-8 555 timer IC

1 x 3-pin through hole potentiometer, 10K to 50K recommended

Show full description

TESTED AND WORKING

(Support will only be offered on projects marked "TESTED AND WORKING", and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with NO reverse polarit…

TESTED AND WORKING

(Support will only be offered on projects marked “TESTED AND WORKING”, and only on the moxbods facebook group.

Any previous projects that are now deleted are used at your own risk.)

This is a PWM board with NO reverse polarity protection.

Recommended potentiometer value: 10K - 50K

Parts list:

1 x 0603 1K resistor

1 x 0603 0.1uF capacitor

1 x 0603 0.01uF capacitor

1 x BAT54S dual diode (SOT23 package)

1 x SOIC-8 555 timer IC

1 x 3-pin through hole potentiometer, 10K to 50K recommended

Show full description

Embeddable link to order this shared Project

eagleboard004.brd

author: Skeeter

2 layer board of 1.00 x 0.50 inches (25.4 x 12.7 mm)
Uploaded: June 30, 2015
Shared: October 05, 2016
Total Price: $2.50

capacitor to terminal blocks
there's probably no good use for this

Embeddable link to order this shared Project

PCB Outline.zip

author: MuffinMan

2 layer board of 2.08 x 1.85 inches (52.9 x 47.0 mm)
Uploaded: October 04, 2016
Shared: October 04, 2016
Total Price: $19.20

Class E Amplifier

Embeddable link to order this shared Project

CANTransceivernonISOV2.1

author: ashruhan

2 layer board of 0.98 x 0.29 inches (24.9 x 7.3 mm)
Uploaded: October 04, 2016
Shared: October 04, 2016
Total Price: $1.40