OSH Park ~ Shared Projects

Zoomieleven driver

author: DavidEF

2 layer board of 0.45 x 0.45 inches (11.4 x 11.4 mm)
Uploaded: April 14, 2017
Shared: April 14, 2017
Total Price: $1.00

I made this driver to fit in a tiny zoomable keychain flashlight I found at Lowe’s Home Improvement. The flashlight comes with a cheap LED on a PCB, and no driver. It uses 4 button cells to power the LED directly. There is a clicky switch in the tail of the flashlight. It’s the smallest zoomable …

I made this driver to fit in a tiny zoomable keychain flashlight I found at Lowe’s Home Improvement. The flashlight comes with a cheap LED on a PCB, and no driver. It uses 4 button cells to power the LED directly. There is a clicky switch in the tail of the flashlight. It’s the smallest zoomable I’ve ever seen, and probably the smallest flashlight I’ve ever seen with a clicky switch. Since there is no driver, with a single PCB containing only the LED, I decided to make this driver board with all the driver components on one side and the LED pads on the other side so that it would be a drop-in solution. This driver is made to be small, but still have direct-drive level power output to the LED. OSH Park requires a 15mil distance to the dimensional outline to be free of copper so I padded the board by that much around the edge. If you sand down to the edge of the copper pour, this board will be 11mm diameter. That is the diameter I need for the flashlight that I have in mind for this board. This driver uses the 10 pin Atmel Tiny13a MMU chip and a LFPAK33 FET. The LED footprint is made for any CREE XP or similar LED.

Show full description

I made this driver to fit in a tiny zoomable keychain flashlight I found at Lowe’s Home Improvement. The flashlight comes with a cheap LED on a PCB, and no driver. It uses 4 button cells to power the LED directly. There is a clicky switch in the tail of the flashlight. It’s the smallest zoomable …

I made this driver to fit in a tiny zoomable keychain flashlight I found at Lowe’s Home Improvement. The flashlight comes with a cheap LED on a PCB, and no driver. It uses 4 button cells to power the LED directly. There is a clicky switch in the tail of the flashlight. It’s the smallest zoomable I’ve ever seen, and probably the smallest flashlight I’ve ever seen with a clicky switch. Since there is no driver, with a single PCB containing only the LED, I decided to make this driver board with all the driver components on one side and the LED pads on the other side so that it would be a drop-in solution. This driver is made to be small, but still have direct-drive level power output to the LED. OSH Park requires a 15mil distance to the dimensional outline to be free of copper so I padded the board by that much around the edge. If you sand down to the edge of the copper pour, this board will be 11mm diameter. That is the diameter I need for the flashlight that I have in mind for this board. This driver uses the 10 pin Atmel Tiny13a MMU chip and a LFPAK33 FET. The LED footprint is made for any CREE XP or similar LED.

Show full description

Embeddable link to order this shared Project

STM051 minimal

author: Anton_Chromjak

2 layer board of 0.63 x 1.52 inches (16.1 x 38.7 mm)
Uploaded: April 21, 2015
Shared: April 14, 2017
Total Price: $4.80

STM051 minimal board

STM051 minimal board

Embeddable link to order this shared Project

PMSM

author: Anton_Chromjak

2 layer board of 0.73 x 2.14 inches (18.4 x 54.3 mm)
Uploaded: February 16, 2016
Shared: April 14, 2017
Total Price: $7.75

PMSM control

PMSM control

Embeddable link to order this shared Project

gps-small.zip

author: night_ghost

2 layer board of 0.99 x 0.99 inches (25.2 x 25.2 mm)
Uploaded: April 14, 2017
Shared: April 14, 2017
Total Price: $4.90

This board designed for transplanting parts from this board - https://ru.aliexpress.com/item/FREE-SHIPPING-GPS-GLONASS-Module-GNSS-MT3333-PA6E-CAM-FGPMMOPA6E-breakout-Titan-1-10Hz-115200bps/32440564245.html

This board designed for transplanting parts from this board - https://ru.aliexpress.com/item/FREE-SHIPPING-GPS-GLONASS-Module-GNSS-MT3333-PA6E-CAM-FGPMMOPA6E-breakout-Titan-1-10Hz-115200bps/32440564245.html

Embeddable link to order this shared Project

WS2812 Breakout Rev 0

author: arbartz

2 layer board of 2.53 x 2.53 inches (64.3 x 64.3 mm)
Uploaded: April 14, 2017
Shared: April 14, 2017
Total Price: $32.00

Embeddable link to order this shared Project

nixieAux.brd

author: capricorn_one

2 layer board of 2.56 x 0.59 inches (65.0 x 15.0 mm)
Uploaded: September 17, 2016
Shared: April 14, 2017
Total Price: $7.55

nixiePlanter Jacks and Switches

nixiePlanter Jacks and Switches

Embeddable link to order this shared Project

esp-12 2side v2

author: cperiod

2 layer board of 1.06 x 2.03 inches (26.8 x 51.6 mm)
Uploaded: March 25, 2017
Shared: April 14, 2017
Total Price: $10.70

Basic ESP-12 dev board, derived from a single-sided home-etched version using (mostly) through-hole components I have on hand. 1x AMS1117-33, 4x 10k R, 2x 10-22uF, 1x 100pF, 1x slide switch, 1x screw terminal, 2x tact switches, (optional) LED+resistor, assorted headers (I mount my ESP-12's on 2mm…

Basic ESP-12 dev board, derived from a single-sided home-etched version using (mostly) through-hole components I have on hand. 1x AMS1117-33, 4x 10k R, 2x 10-22uF, 1x 100pF, 1x slide switch, 1x screw terminal, 2x tact switches, (optional) LED+resistor, assorted headers (I mount my ESP-12’s on 2mm headers).

You can also swap the AMS1117 with a TO-92 HT7333 for low quiescent power applications (i.e. 3.7v Li-ion).

Show full description

Basic ESP-12 dev board, derived from a single-sided home-etched version using (mostly) through-hole components I have on hand. 1x AMS1117-33, 4x 10k R, 2x 10-22uF, 1x 100pF, 1x slide switch, 1x screw terminal, 2x tact switches, (optional) LED+resistor, assorted headers (I mount my ESP-12's on 2mm…

Basic ESP-12 dev board, derived from a single-sided home-etched version using (mostly) through-hole components I have on hand. 1x AMS1117-33, 4x 10k R, 2x 10-22uF, 1x 100pF, 1x slide switch, 1x screw terminal, 2x tact switches, (optional) LED+resistor, assorted headers (I mount my ESP-12’s on 2mm headers).

You can also swap the AMS1117 with a TO-92 HT7333 for low quiescent power applications (i.e. 3.7v Li-ion).

Show full description

Embeddable link to order this shared Project

PE3 PWM Driver P-CH (1-18-2016)

author: matthew.martin8

2 layer board of 0.72 x 0.55 inches (18.2 x 14.0 mm)
Uploaded: February 19, 2016
Shared: April 13, 2017
Total Price: $1.95

PE3 PWM Driver P-CH (1-18-2016)

PE3 PWM Driver P-CH (1-18-2016)

Embeddable link to order this shared Project

Ys

author: kenbrownlab

2 layer board of 3.05 x 2.14 inches (77.5 x 54.3 mm)
Uploaded: July 27, 2015
Shared: April 13, 2017
Total Price: $32.60

Embeddable link to order this shared Project

motor_shield__SD_v1.1.brd

author: sshriya

2 layer board of 3.04 x 2.05 inches (77.2 x 52.1 mm)
Uploaded: April 13, 2017
Shared: April 13, 2017
Total Price: $31.10

Senior design Motor Shield

Senior design Motor Shield

Embeddable link to order this shared Project

eink controller

author: julbouln

2 layer board of 2.61 x 2.31 inches (66.3 x 58.7 mm)
Uploaded: August 24, 2016
Shared: April 13, 2017
Total Price: $30.15

ice40 based eink controller https://github.com/julbouln/ice40_eink_controller

ice40 based eink controller https://github.com/julbouln/ice40_eink_controller

Embeddable link to order this shared Project

CATS HAT v0.2.1

author: ophilli

2 layer board of 2.53 x 2.17 inches (64.2 x 55.2 mm)
Uploaded: April 13, 2017
Shared: April 13, 2017
Total Price: $27.40

github.com/clemsonMakerspace/CATS

github.com/clemsonMakerspace/CATS

Embeddable link to order this shared Project

SMA Pulse Generator

author: subhagato

2 layer board of 2.51 x 2.75 inches (63.7 x 69.8 mm)
Uploaded: April 13, 2017
Shared: April 13, 2017
Total Price: $34.45

Embeddable link to order this shared Project

RPi Power Monitor Hat (SMPS)

author: tim

2 layer board of 2.56 x 1.18 inches (65.0 x 30.0 mm)
Uploaded: March 19, 2017
Shared: April 13, 2017
Total Price: $15.10

Embeddable link to order this shared Project

Back Porch Generator

author: Serge

2 layer board of 1.50 x 1.10 inches (38.2 x 28.0 mm)
Uploaded: September 24, 2013
Shared: April 13, 2017
Total Price: $8.30

Back Porch Generator for ZX80

Back Porch Generator for ZX80

Embeddable link to order this shared Project

RaspNRF24-V2.brd

author: GertSanders

2 layer board of 1.40 x 0.75 inches (35.6 x 19.0 mm)
Uploaded: December 29, 2016
Shared: April 13, 2017
Total Price: $5.25

RaspNRF24-V2, tested to work. C1 is 100uF C2 is 10uF C3 is 100nF IC1 is ASM1117 3.3V The NRF24L01 is a module with ceramic antenna. This sits on the top side. The IRQ pin is connected to PIN18 on the Raspberry header. The two row header starts at pin 1 (where JP1 is written) and sits on the…

RaspNRF24-V2, tested to work. C1 is 100uF C2 is 10uF C3 is 100nF IC1 is ASM1117 3.3V The NRF24L01 is a module with ceramic antenna. This sits on the top side. The IRQ pin is connected to PIN18 on the Raspberry header. The two row header starts at pin 1 (where JP1 is written) and sits on the bottom side. Fits inside most Raspberry2 cases.

Show full description

RaspNRF24-V2, tested to work. C1 is 100uF C2 is 10uF C3 is 100nF IC1 is ASM1117 3.3V The NRF24L01 is a module with ceramic antenna. This sits on the top side. The IRQ pin is connected to PIN18 on the Raspberry header. The two row header starts at pin 1 (where JP1 is written) and sits on the…

RaspNRF24-V2, tested to work. C1 is 100uF C2 is 10uF C3 is 100nF IC1 is ASM1117 3.3V The NRF24L01 is a module with ceramic antenna. This sits on the top side. The IRQ pin is connected to PIN18 on the Raspberry header. The two row header starts at pin 1 (where JP1 is written) and sits on the bottom side. Fits inside most Raspberry2 cases.

Show full description

Embeddable link to order this shared Project

Chorus VTX PCB

author: joner

2 layer board of 1.24 x 1.65 inches (31.4 x 41.9 mm)
Uploaded: April 13, 2017
Shared: April 13, 2017
Total Price: $10.20

PCB for https://github.com/voroshkov/Chorus-RF-Laptimer

PCB for https://github.com/voroshkov/Chorus-RF-Laptimer

Embeddable link to order this shared Project

board-ignition.zip

author: night_ghost

2 layer board of 1.77 x 1.77 inches (45.0 x 45.0 mm)
Uploaded: April 03, 2017
Shared: April 13, 2017
Total Price: $15.65

HF ballast for SHAAZ heater

board for http://www.gorbunov.narod.ru/grubka.html

HF ballast for SHAAZ heater

board for http://www.gorbunov.narod.ru/grubka.html

Embeddable link to order this shared Project

board_roundGPS.zip

author: night_ghost

2 layer board of 1.39 x 1.39 inches (35.2 x 35.2 mm)
Uploaded: April 03, 2017
Shared: April 13, 2017
Total Price: $9.60

board for GMS-g9 GPS module

This board designed for transplanting parts from this board - https://ru.aliexpress.com/item/FREE-SHIPPING-GPS-GLONASS-Module-GNSS-MT3333-PA6E-CAM-FGPMMOPA6E-breakout-Titan-1-10Hz-115200bps/32440564245.html

board for GMS-g9 GPS module

This board designed for transplanting parts from this board - https://ru.aliexpress.com/item/FREE-SHIPPING-GPS-GLONASS-Module-GNSS-MT3333-PA6E-CAM-FGPMMOPA6E-breakout-Titan-1-10Hz-115200bps/32440564245.html

Embeddable link to order this shared Project

Adafruit M0 Feather DWM1000 v1.zip

author: rbrainard

2 layer board of 2.42 x 0.91 inches (61.4 x 23.0 mm)
Uploaded: March 28, 2017
Shared: April 13, 2017
Total Price: $10.90

Embeddable link to order this shared Project

COMPANY
About Us
Blog
Shop

HELP
Support
If you can't find what you're looking for, please contact us at [email protected]

Whaleshark white

© Copyright 2025 OSH Park, LLC | Privacy