D1 Mini Coin Battery
author: deshipu
2 layer board of 1.01 x 1.12 inches (25.8 x 28.5 mm)
Uploaded:
October 31, 2017
Shared:
November 09, 2017
Total Price:
$5.65
A shield for D1 Mini with a coin battery and charger. https://hackaday.io/project/28104
A shield for D1 Mini with a coin battery and charger. https://hackaday.io/project/28104
FX Order Switching
author: BryGuy
2 layer board of 0.97 x 0.72 inches (24.5 x 18.2 mm)
Uploaded:
November 09, 2017
Shared:
November 09, 2017
Total Price:
$3.45
Use a 3PDT toggle switch to change the order of two guitar fx in one enclosure. Toggle switch can be inserted from the bottom or the top of the pcb. Just follow the ins and outs and you should be fine.
-VERIFIED-
Use a 3PDT toggle switch to change the order of two guitar fx in one enclosure. Toggle switch can be inserted from the bottom or the top of the pcb. Just follow the ins and outs and you should be fine.
-VERIFIED-
OptoInterrupterShield V2 for ProMini PiDuino HAT
author: dewhisna
2 layer board of 2.11 x 2.23 inches (53.5 x 56.7 mm)
Uploaded:
October 08, 2017
Shared:
November 09, 2017
Total Price:
$23.45
The Optical Interrupter Shield V2 board, for ProMini PiDuino HAT, was designed to interface four off-the-shelf optical reflective sensors, such as my QRE1113 Sensor Board, used in raw-sensor mode, to a Raspberry Pi via an Arduino ProMini PiDuino…
Show full description
The Optical Interrupter Shield V2 board, for ProMini PiDuino HAT, was designed to interface four off-the-shelf optical reflective sensors, such as my QRE1113 Sensor Board, used in raw-sensor mode, to a Raspberry Pi via an Arduino ProMini PiDuino…
Show full description
Nixie tube power supply
author: judge2005
2 layer board of 1.46 x 0.91 inches (37.0 x 23.0 mm)
Uploaded:
November 09, 2017
Shared:
November 09, 2017
Total Price:
$6.55
A power supply for nixie tubes. Input voltage can be from 3V to 12V. Output voltage can be 0V to 200V. See my web site for links to full project documentation, parts lists, KiCAD project etc.
A power supply for nixie tubes. Input voltage can be from 3V to 12V. Output voltage can be 0V to 200V. See my web site for links to full project documentation, parts lists, KiCAD project etc.
GR10J Nixie tube breadboard adapter
author: judge2005
2 layer board of 1.31 x 1.36 inches (33.2 x 34.4 mm)
Uploaded:
October 11, 2017
Shared:
November 08, 2017
Total Price:
$8.80
A breadboard adapter for the GR10J Numicator (Nixie). These tubes have 1mm pins that plug in to a socket. This board is intended to use female D-SUB pins as a 'socket'. These are often listed on eBay as '[1mm tube socket pins](https://www.ebay.com/sch/nixietubeclock/m.html?nkw=&armrs=1&ipg=&f…
Show full description
A breadboard adapter for the GR10J Numicator (Nixie). These tubes have 1mm pins that plug in to a socket. This board is intended to use female D-SUB pins as a 'socket'. These are often listed on eBay as '[1mm tube socket pins](https://www.ebay.com/sch/nixietubeclock/m.html?nkw=&armrs=1&ipg=&f…
Show full description
Alien 16.8mm contact board_V4.brd
author: ArcticDude
2 layer board of 0.66 x 0.66 inches (16.8 x 16.8 mm)
Uploaded:
November 08, 2017
Shared:
November 08, 2017
Total Price:
$2.15
BoostConverter.v01a
author: PeskyProducts
2 layer board of 0.36 x 0.26 inches (9.0 x 6.5 mm)
Uploaded:
November 08, 2017
Shared:
November 08, 2017
Total Price:
$0.45
TI TPS610994 3V3 boost converter breakout.
TI TPS610994 3V3 boost converter breakout.
Temp Sensor
author: GodoStoyke
2 layer board of 4.41 x 0.91 inches (111.9 x 23.0 mm)
Uploaded:
June 08, 2016
Shared:
November 08, 2017
Total Price:
$19.90
Temp Sensor
Temp Sensor
keyTop.brd
author: petay
2 layer board of 1.50 x 3.00 inches (38.2 x 76.2 mm)
Uploaded:
November 07, 2017
Shared:
November 07, 2017
Total Price:
$22.50
A custom keayboard top plate maker. All holes are 2.5mm and plated, so any holes can either be bolted or soldered together!! Use 0.8mm pcb to allow boards overlapping for strength, and you will end up with 1.6mm thickness :) UNTESTED!!
A custom keayboard top plate maker. All holes are 2.5mm and plated, so any holes can either be bolted or soldered together!! Use 0.8mm pcb to allow boards overlapping for strength, and you will end up with 1.6mm thickness :) UNTESTED!!
