AJQuick 4-Axis CNC Controller Board
author: IOTLLC
2 layer board of 7.20 x 2.20 inches (182.9 x 55.9 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$79.20
CNC Controller is a Unipolar Stepper motor controller based on the SLA7078MPR by Allegro Microsystems
CNC Controller is a Unipolar Stepper motor controller based on the SLA7078MPR by Allegro Microsystems
Cat Laser Control Board
author: stuthedew
2 layer board of 1.70 x 1.70 inches (43.2 x 43.2 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$14.40
See https://github.com/stuthedew/Arduino-Laser-Cat-Turret
See https://github.com/stuthedew/Arduino-Laser-Cat-Turret
Raspberry Pi Hub75-Dual v1.1
author: CaptainMurdoch
2 layer board of 1.44 x 1.00 inches (36.5 x 25.4 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$7.15
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a set of HUB75 compatible LED panel into the GPIO header on…
Show full description
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a set of HUB75 compatible LED panel into the GPIO header on…
Show full description
Raspberry Pi Hub75 v1.1
author: CaptainMurdoch
2 layer board of 1.44 x 0.65 inches (36.5 x 16.5 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$4.65
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a HUB75 compatible LED panel into the GPIO header on a Rasp…
Show full description
NOTE: This board uses the OLD pinout and the rpi-rgb-led-matrix library must be specifically compiled to work with this version. If you are a FPP user, check on the forums before ordering any of this board.
This board allows plugging a HUB75 compatible LED panel into the GPIO header on a Rasp…
Show full description
Icetube Clock - Transistor - Rev C
author: PhilD13
2 layer board of 4.50 x 1.08 inches (114.4 x 27.4 mm)
Uploaded:
February 06, 2015
Shared:
February 06, 2015
Total Price:
$24.25
A version of the Adafruit Icetube clock main board that will accept either a ZVP2110A FET (use a jumper wire for R6) or a PN2907 transistor for Q3 and use 470 ohm (min value) - 1K ohm (max value) for resistor R6. Suggest using firmware found here for the clock. https://github.com/johngarchie/xm…
Show full description
A version of the Adafruit Icetube clock main board that will accept either a ZVP2110A FET (use a jumper wire for R6) or a PN2907 transistor for Q3 and use 470 ohm (min value) - 1K ohm (max value) for resistor R6. Suggest using firmware found here for the clock. https://github.com/johngarchie/xm…
Show full description
Alps EC11K15 breadboard helper v1.1
author: djm
2 layer board of 1.20 x 1.00 inches (30.5 x 25.4 mm)
Uploaded:
December 01, 2014
Shared:
February 06, 2015
Total Price:
$6.00
A breadboard adapter for an Alps EC11K15 rotary encoder that includes pullup resistors and debouncing caps. Connector pins ensure the helper board sits firmly on the breadboard beneath.
A breadboard adapter for an Alps EC11K15 rotary encoder that includes pullup resistors and debouncing caps. Connector pins ensure the helper board sits firmly on the breadboard beneath.
X360 Power Adapter
author: Element18592
2 layer board of 3.80 x 1.56 inches (96.5 x 39.7 mm)
Uploaded:
February 04, 2015
Shared:
February 06, 2015
Total Price:
$29.65
A Molex and USB adapter powered by the Xbox 360 Phat PSU.
A Molex and USB adapter powered by the Xbox 360 Phat PSU.
Keyboard Shield
author: mikegreenberg
2 layer board of 2.70 x 2.10 inches (68.6 x 53.3 mm)
Uploaded:
September 22, 2014
Shared:
February 06, 2015
Total Price:
$28.30
Nixie Clock v4
author: calpolyieee
2 layer board of 1.90 x 2.04 inches (48.3 x 51.8 mm)
Uploaded:
February 05, 2015
Shared:
February 05, 2015
Total Price:
$19.35
Poison Dart
author: NeonSilicon
2 layer board of 1.24 x 1.04 inches (31.4 x 26.3 mm)
Uploaded:
February 15, 2014
Shared:
February 05, 2015
Total Price:
$6.40
MOSFET treble boost Project doc is at Rock.it-Frog.com
MOSFET treble boost Project doc is at Rock.it-Frog.com
ESP8266 Breakout
author: pretenda
2 layer board of 0.80 x 1.27 inches (20.3 x 32.3 mm)
Uploaded:
February 04, 2015
Shared:
February 04, 2015
Total Price:
$5.05
ESP8266 Breakout Board.
You'll need an LM1117 for the voltage regulator and a mini USB connector for power.
The ESP8266 stacks on top of the breakout. (The antenna sits over top of the USB connector)
ESP8266 Breakout Board.
You'll need an LM1117 for the voltage regulator and a mini USB connector for power.
The ESP8266 stacks on top of the breakout. (The antenna sits over top of the USB connector)
TinyTeRPs Light Sensor Board
author: CRL
2 layer board of 0.40 x 0.55 inches (10.2 x 14.0 mm)
Uploaded:
February 04, 2015
Shared:
February 04, 2015
Total Price:
$1.10
MicroRobotics Lab @ University of Maryland! Take a look at mrl.umd.edu for more details, schematics, and software!
MicroRobotics Lab @ University of Maryland! Take a look at mrl.umd.edu for more details, schematics, and software!
