Shared Projects

Shared Projects

Remote Sensor Base

author: gvi70000

2 layer board of 1.51 x 2.10 inches (38.4 x 53.4 mm)
Uploaded: May 28, 2015
Shared: May 28, 2015
Total Price: $15.85

Remote Sensor Base

Remote Sensor Base

Embeddable link to order this shared Project

Atmel SAM3S/N board

author: Lt_Flash

2 layer board of 1.61 x 1.76 inches (40.9 x 44.7 mm)
Uploaded: October 31, 2014
Shared: May 28, 2015
Total Price: $14.15

Development board for Atmel SAM3

Development board for Atmel SAM3

Embeddable link to order this shared Project

Li-Po Fuel Gauge

author: Lt_Flash

2 layer board of 1.60 x 0.45 inches (40.6 x 11.5 mm)
Uploaded: January 10, 2015
Shared: May 28, 2015
Total Price: $3.60

System-side BQ27200-based I2C battery fuel gauge breakout

System-side BQ27200-based I2C battery fuel gauge breakout

Embeddable link to order this shared Project

BA7230LS RGB to Component v5.0A

author: Helder

2 layer board of 1.60 x 1.94 inches (40.6 x 49.2 mm)
Uploaded: May 28, 2015
Shared: May 28, 2015
Total Price: $15.50

Through hole board for Ace's schematic v5.0, must use the 2SC945 NPN transistor because of the pinout. Untested but should work.

Through hole board for Ace's schematic v5.0, must use the 2SC945 NPN transistor because of the pinout. Untested but should work.

Embeddable link to order this shared Project

40CH RX for Racingrecorder

author: Moe_fpv_team_de

2 layer board of 0.99 x 1.73 inches (25.2 x 44.0 mm)
Uploaded: May 27, 2015
Shared: May 27, 2015
Total Price: $8.60

Special 40CH RX Module for my Racerecorder

Special 40CH RX Module for my Racerecorder

Embeddable link to order this shared Project

nRf24L01+.v02yy.t3

author: PeskyProducts

2 layer board of 0.71 x 0.70 inches (18.0 x 17.8 mm)
Uploaded: May 27, 2015
Shared: May 27, 2015
Total Price: $2.45

Nordic Semiconductor’s low-power 2.4 GHz RF radio with pcb antenna and matching circuit per Nordic’s spec. Using much smaller XRCHA16MHz Murata crystal to reduce cost and board size. Added solder jumpers on back to allow 3V3 and GND to be taken from board edge to make breadboard friendly.

Nordic Semiconductor’s low-power 2.4 GHz RF radio with pcb antenna and matching circuit per Nordic’s spec. Using much smaller XRCHA16MHz Murata crystal to reduce cost and board size. Added solder jumpers on back to allow 3V3 and GND to be taken from board edge to make breadboard friendly.

Embeddable link to order this shared Project

UyMods Micro PFet PWM

author: Pathian

2 layer board of 0.61 x 0.41 inches (15.4 x 10.3 mm)
Uploaded: May 27, 2015
Shared: May 27, 2015
Total Price: $1.20

Parts List: http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=8f58c48b46

Wire through holes made for 26awg hookup wire.

Parts List: http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=8f58c48b46

Wire through holes made for 26awg hookup wire.

Embeddable link to order this shared Project

driver1

author: boikonur

2 layer board of 1.19 x 1.19 inches (30.2 x 30.2 mm)
Uploaded: April 02, 2015
Shared: May 27, 2015
Total Price: $7.05

driver1

driver1

Embeddable link to order this shared Project

33-5rs232bo_revA

author: bradfa

2 layer board of 1.30 x 0.98 inches (33.1 x 24.9 mm)
Uploaded: April 23, 2015
Shared: May 27, 2015
Total Price: $6.35

3.3 to 5 V RS232 Breakout revision A

3.3 to 5 V RS232 Breakout revision A

Embeddable link to order this shared Project

A simple relay board

author: Dumle29

2 layer board of 1.68 x 1.04 inches (42.6 x 26.4 mm)
Uploaded: May 27, 2015
Shared: May 27, 2015
Total Price: $8.65

well yeah.

well yeah.

Embeddable link to order this shared Project

MLX90620 BRD

author: kevoarsys

2 layer board of 0.72 x 1.04 inches (18.2 x 26.4 mm)
Uploaded: May 26, 2015
Shared: May 27, 2015
Total Price: $3.70

THERMIC ARRAY BOARD

THERMIC ARRAY BOARD

Embeddable link to order this shared Project

MOSFET BOARD

author: kevoarsys

2 layer board of 0.91 x 1.16 inches (23.1 x 29.4 mm)
Uploaded: May 26, 2015
Shared: May 27, 2015
Total Price: $5.25

3w driver single way

3w driver single way

Embeddable link to order this shared Project

Power led pcb

author: kevoarsys

2 layer board of 0.96 x 0.31 inches (24.3 x 7.8 mm)
Uploaded: May 26, 2015
Shared: May 27, 2015
Total Price: $1.45

3 w led

3 w led

Embeddable link to order this shared Project

GAS BOARD

author: kevoarsys

2 layer board of 3.45 x 1.82 inches (87.7 x 46.2 mm)
Uploaded: May 27, 2015
Shared: May 27, 2015
Total Price: $31.40

THREE GAS SENSOR BOARD

THREE GAS SENSOR BOARD

Embeddable link to order this shared Project

AS5048

author: kevoarsys

2 layer board of 0.58 x 1.13 inches (14.6 x 28.8 mm)
Uploaded: May 27, 2015
Shared: May 27, 2015
Total Price: $3.25

Magnetic encoder board

Magnetic encoder board

Embeddable link to order this shared Project

3.5mm and 2.5mm Audio Breakout Rev A

author: mikem

2 layer board of 1.85 x 0.52 inches (47.0 x 13.3 mm)
Uploaded: May 26, 2015
Shared: May 26, 2015
Total Price: $4.80

3.5mm and 2.5mm Audio Breakout

3.5mm and 2.5mm Audio Breakout

Embeddable link to order this shared Project

STM32F070 Breakout

author: emeb

2 layer board of 2.22 x 0.82 inches (56.3 x 20.7 mm)
Uploaded: May 07, 2015
Shared: May 26, 2015
Total Price: $9.00

V0.1

V0.1

Embeddable link to order this shared Project

USB 4 SERIAL POD

author: BHelix

2 layer board of 1.46 x 1.96 inches (37.2 x 49.8 mm)
Uploaded: November 23, 2014
Shared: May 26, 2015
Total Price: $14.35

USB to 4 Port Serial Pod

USB to 4 Port Serial Pod

Embeddable link to order this shared Project

6509 BOARD V2

author: randybob

2 layer board of 2.95 x 3.53 inches (74.8 x 89.7 mm)
Uploaded: May 26, 2015
Shared: May 26, 2015
Total Price: $52.00

TEST BOARD

TEST BOARD

Embeddable link to order this shared Project

UTexas BWI - Power Distribution Board

author: patopop007

2 layer board of 6.52 x 1.99 inches (165.6 x 50.6 mm)
Uploaded: April 30, 2015
Shared: May 26, 2015
Total Price: $64.85

Board for distributing unregulated 12v and regulated 12v/5v to all our sensors and actuators.

Board for distributing unregulated 12v and regulated 12v/5v to all our sensors and actuators.

Embeddable link to order this shared Project