PI232B v1
author: NF6X
2 layer board of 2.51 x 0.96 inches (63.6 x 24.3 mm)
Uploaded:
June 27, 2015
Shared:
July 12, 2015
Total Price:
$11.95
RS232 level shifter for the Raspberry Pi Model B
by Mark J. Blair <[email protected]>
This board is an RS232 level shifter for the Raspberry Pi Model B, which is the version with a 26-pin J1 next to an 8-pin J5. It is not intended for use with any other versions of the Raspberry Pi board. …
Show full description
RS232 level shifter for the Raspberry Pi Model B
by Mark J. Blair <[email protected]>
This board is an RS232 level shifter for the Raspberry Pi Model B, which is the version with a 26-pin J1 next to an 8-pin J5. It is not intended for use with any other versions of the Raspberry Pi board. …
Show full description
nRF24L01+.v03.t3
2 layer board of 0.71 x 0.70 inches (18.0 x 17.8 mm)
Uploaded:
July 11, 2015
Shared:
July 11, 2015
Total Price:
$2.45
Nordic Semiconductor’s low-power 2.4 GHz RF radio with pcb antenna and matching circuit per Nordic’s spec. Using much smaller XRCHA16MHz Murata crystal to reduce cost and board size. Added solder jumpers on back to allow 3V3 and GND to be taken from board edge to make breadboard friendly. Replace…
Show full description
Nordic Semiconductor’s low-power 2.4 GHz RF radio with pcb antenna and matching circuit per Nordic’s spec. Using much smaller XRCHA16MHz Murata crystal to reduce cost and board size. Added solder jumpers on back to allow 3V3 and GND to be taken from board edge to make breadboard friendly. Replace…
Show full description
Arduino Mega
author: jeffarduino
2 layer board of 4.01 x 2.11 inches (101.9 x 53.6 mm)
Uploaded:
July 11, 2015
Shared:
July 11, 2015
Total Price:
$42.30
Micro SD card Wasp/Wiikey Fusion replacement Rev 2
author: bentomo
2 layer board of 1.94 x 0.68 inches (49.2 x 17.4 mm)
Uploaded:
July 11, 2015
Shared:
July 11, 2015
Total Price:
$6.60
The is the second revision of the wiikey/wasp fusion sd card replacement board with repaired gnd trace.
The is the second revision of the wiikey/wasp fusion sd card replacement board with repaired gnd trace.
Train latching relay
author: Wire
2 layer board of 1.26 x 1.01 inches (31.9 x 25.6 mm)
Uploaded:
July 11, 2015
Shared:
July 11, 2015
Total Price:
$6.30
Train latching relay for O gauge trains. ~9 to 20Vac or ~9 to 14Vdc
Train latching relay for O gauge trains. ~9 to 20Vac or ~9 to 14Vdc
Breadboard dual power supply
author: adent
2 layer board of 2.34 x 0.85 inches (59.4 x 21.6 mm)
Uploaded:
April 24, 2013
Shared:
July 10, 2015
Total Price:
$9.90
Dual power supply (5V + 3.3V) for your breadboard, based on Linear Technology's LT1529 low dropout regulators.
Dual power supply (5V + 3.3V) for your breadboard, based on Linear Technology's LT1529 low dropout regulators.
B-15N bias pot V1.2
author: bax
2 layer board of 1.02 x 1.02 inches (26.0 x 26.0 mm)
Uploaded:
July 10, 2015
Shared:
July 10, 2015
Total Price:
$5.20
Ampeg 1974 B-15N bias pot
Bourns 3250W-1-203 this is a multi-turn, 20K linear taper pot. A 25KL such as a 3296W-1-253 will work as well. The required pin spacing is 0.1".
The total target resistance with the pot and serially connected resistor is 47K ohms. The design allows for either a …
Show full description
Ampeg 1974 B-15N bias pot
Bourns 3250W-1-203 this is a multi-turn, 20K linear taper pot. A 25KL such as a 3296W-1-253 will work as well. The required pin spacing is 0.1".
The total target resistance with the pot and serially connected resistor is 47K ohms. The design allows for either a …
Show full description
SOIC-DIP14 adapter bottom board, v0.2
author: Smugrik
2 layer board of 0.70 x 0.42 inches (17.8 x 10.7 mm)
Uploaded:
July 09, 2015
Shared:
July 09, 2015
Total Price:
$1.45
An adapter to fit a Soic14 IC in a Dip14 socket
You also need the top board
An adapter to fit a Soic14 IC in a Dip14 socket
You also need the top board
SOIC-DIP14 adapter top board, v0.2
author: Smugrik
2 layer board of 0.70 x 0.42 inches (17.8 x 10.7 mm)
Uploaded:
July 09, 2015
Shared:
July 09, 2015
Total Price:
$1.45
An adapter to fit a Soic14 IC in a Dip14 socket
You also need the bottom board
An adapter to fit a Soic14 IC in a Dip14 socket
You also need the bottom board
Femtoduino USB, r14.2
author: femtoduino
4 layer board of 0.82 x 0.60 inches (20.7 x 15.3 mm)
Uploaded:
May 07, 2015
Shared:
July 09, 2015
Total Price:
$4.80
Smallest Arduino UNO compatible, with built in FTDI chip for USB support.
Smallest Arduino UNO compatible, with built in FTDI chip for USB support.