Shared Projects

Particle Photon, Electron and Spark Core JTAG Shield Debugger

Simple board to combine a Teensy and some Cherry MX switches as a macro key bar. Has i2c header for attaching display.

CC-4.0-BY-SA License, EAGLE design files on github:

https://github.com/schizobovine/clickclack

RC XT Charging and Balance Board BOM Parts list for one (1) PCB

Note: There are two different versions of XH headers: one with a tab and one without. The one listed below is the one without the tab. The tabbed one will not fit. The crimp allows for 22AWG wire to be used as the smallest size. There is another version that will fit 26AWG Wire as a minimum. My version uses 22AWG wire but smaller wire will also work. XT connectors need to be trimmed so they bottom does not stick out too far past the board.

7x JST-XH Connector Crimp: SXH-001T-P0.6 http://www.digikey.com/product-detail/en/SXH-001T-P0.6/455-1135-1-ND/527370

1x JST-XH 7 Position Female Connector Housing: XHP-7 http://www.digikey.com/product-search/en?mpart=XHP-7&vendor=455

1x JST-XH 3 Position Male Header: B3B-XH-A(LF)(SN) http://www.digikey.com/product-search/en?mpart=B3B-XH-A%28LF%29%28SN%29&vendor=455

1x JST-XH 4 Position Male Header: B4B-XH-A(LF)(SN) http://www.digikey.com/product-search/en?mpart=B4B-XH-A%28LF%29%28SN%29&vendor=455

1x JST-XH 5 Position Male Header: B5B-XH-A(LF)(SN) http://www.digikey.com/product-search/en?mpart=B5B-XH-A%28LF%29%28SN%29&vendor=455

1x JST-XH 6 Position Male Header: B6B-XH-A(LF)(SN) http://www.digikey.com/product-search/en?mpart=B6B-XH-A%28LF%29%28SN%29&vendor=455

1x JST-XH 7 Position Male Header: B7B-XH-A(LF)(SN) http://www.digikey.com/product-search/en?mpart=B7B-XH-AM%28LF%29%28SN%29&vendor=455

1x Barrel Connector 2.1mm Male: PJ-037AH http://www.digikey.com/product-detail/en/PJ-037AH/CP-037AH-ND/1644547

1x Amass XT30 Male

1x Amass XT60 Male

1x Amass XT90 Male

1x Pair of Banana Plugs http://www.amazon.com/gp/product/B007QUYQSY?psc=1&redirect=true&ref_=oh_aui_detailpage_o04_s00

Recommended wire: 16AWG or 14AWG for main power and 22AWG or 24AWG for balance lead.

FT232RL with optoisolators

Revision 4 of my non-SMD pcb designed for use with rx5808-pro-diversity project started by Crazyshea.

Changelog:

Rev 4:

• Added 5v regulator to the rear of the board. Requires ‘DSN-MINI-360’ adjustable step down regulator.

• More Pro Mini pin corrections

Rev 3.1:

• Minor adjustments to routing

• Minor changes to 100k pull down resistors.

Rev 3:

• Fixed hole spacing for Pro Mini

• Fixed DTR, TX, RX etc ports as they were reversed

• Swapped Up and Down Buttons.

• Added 100K pull down resistors on RSSI lines

• Added extra ground and vcc points for pro mini

• Corrected A5 and A4 conenctions

Rev 2:

• Repositioned via holes

Rev 1:

• Initial version

Details can be found on

RCGroups: http://www.rcgroups.com/forums/showthread.php?t=2477752

and Github: https://github.com/sheaivey/rx5808-pro-diversity/blob/master/docs/oled-arduino-nano.md https://github.com/RCDaddy/T-Box

IcomMD CPU version 2 revision 2 carrier board

Because every breadboard project needs some LEDs and buttons.

For testing “QVGA” TFT displays

http://www.pjrc.com/store/display_ili9341_touch.html

Parts used on the board are:

   1    LM7805 voltage regulator        Digikey LM7805ACT-ND
   1    B130 Schottky diode             Digikey B130-FDICT-ND
   1    140 mA PTC fuse                 Digikey 507-1495-1-ND
   1    100 ohm 1/4 watt resistor       Digikey 100XBK-ND
   2    10K ohm 1/4 watt resistor       Digikey 10.0KXBK-ND
   1    DC power jack                   Mouser 163-7620E-E
   1    0.1uF capacitor                 Digikey BC1084CT-ND

How to use Digikey’s website to find alternate parts when any of these aren’t in stock.

mini Brushless Gimbal Controller

mini Brushless Gimbal Controller

http://autoquad.org/wiki/wiki/esc32/can-bus/

just another STM Breakout Board - and untested at the moment

An Arduino Nano shield for the rhythmoid game (github.com/qguv/rhythmoid)

Revision 4 of my non-SMD pcb designed for use with rx5808-pro-diversity project started by Crazyshea.

Changelog:

Rev 4:

• Added 5v regulator to the rear of the board. Requires ‘DSN-MINI-360’ adjustable step down regulator.

Rev 3.1:

• Minor adjustments to routing

• Minor changes to 100k pull down resistors.

Rev 3:

• Fixed hole spacing for Pro Mini

• Fixed DTR, TX, RX etc ports as they were reversed

• Swapped Up and Down Buttons.

• Added 100K pull down resistors on RSSI lines

• Added extra ground and vcc points for pro mini

• Corrected A5 and A4 conenctions

Rev 2:

• Repositioned via holes

Rev 1:

• Initial version

Details can be found on

RCGroups: http://www.rcgroups.com/forums/showthread.php?t=2477752

and Github: https://github.com/sheaivey/rx5808-pro-diversity/blob/master/docs/oled-arduino-nano.md

https://github.com/elmot/open-oscilloscope-stm32f3

soldering-kit version of https://github.com/loansindi/ps1_noise

A breakout board for LPC824