OMSI - Animations - Storyboard
author: hydronics
2 layer board of 3.34 x 3.75 inches (84.8 x 95.2 mm)
Uploaded:
March 06, 2018
Shared:
March 06, 2018
Total Price:
$62.55
Leonardo Shield with Sparkfun multiplexer breakout board 74HC4867 for Parallax RFID Serial Inputs
Leonardo Shield with Sparkfun multiplexer breakout board 74HC4867 for Parallax RFID Serial Inputs
microSD Breakout Board
author: dkonigs
2 layer board of 1.23 x 1.11 inches (31.3 x 28.1 mm)
Uploaded:
March 06, 2018
Shared:
March 06, 2018
Total Price:
$6.80
A simple microSD breakout board with integrated support components. U1 is an EClamp2410P, which provides pull-up resistors and protection diodes for all the data lines. R1 is a pull-up for the card detect signal, and C1 is a capacitor for power.
A simple microSD breakout board with integrated support components. U1 is an EClamp2410P, which provides pull-up resistors and protection diodes for all the data lines. R1 is a pull-up for the card detect signal, and C1 is a capacitor for power.
GCDual YPbPr Multiout QSB
author: citrus3000psi
2 layer board of 0.76 x 0.64 inches (19.2 x 16.2 mm)
Uploaded:
February 19, 2018
Shared:
March 06, 2018
Total Price:
$2.40
This is setup to use HDRetrovisions SNES Multiout connectors. Some small filing might be required to fit. There are 3 small ground pads below some of the pins, this is for the MODE input on the GCDual. if you did NOT setup MODE input on the GCDual then make sure they do not make contact.
St…
Show full description
This is setup to use HDRetrovisions SNES Multiout connectors. Some small filing might be required to fit. There are 3 small ground pads below some of the pins, this is for the MODE input on the GCDual. if you did NOT setup MODE input on the GCDual then make sure they do not make contact.
St…
Show full description
LED Current Source V2
author: BTB
2 layer board of 0.64 x 0.57 inches (16.3 x 14.6 mm)
Uploaded:
February 07, 2018
Shared:
March 06, 2018
Total Price:
$1.80
Simple LED current source for driving LEDs. Built around BC337 series. First Fritzing project, currently untested board.
Simple LED current source for driving LEDs. Built around BC337 series. First Fritzing project, currently untested board.
SMD Challenge R1
author: MakersBox
2 layer board of 1.07 x 1.07 inches (27.1 x 27.1 mm)
Uploaded:
January 02, 2018
Shared:
March 06, 2018
Total Price:
$5.65
BOM and blog at https://hackaday.io/project/25265-an-unfortunate-smd-project
BOM and blog at https://hackaday.io/project/25265-an-unfortunate-smd-project
A40_gerbers
author: alexcp
2 layer board of 3.00 x 3.00 inches (76.2 x 76.2 mm)
Uploaded:
March 05, 2018
Shared:
March 05, 2018
Total Price:
$45.00
Nelson Pass D.I.Y. Project - A40 - a Class A audio power amplifier (one channel per PCB, front end only). See http://www.firstwatt.com/pdf/art_a40.pdf and http://www.firstwatt.com/pdf/art_a40_redux.pdf for details.
Nelson Pass D.I.Y. Project - A40 - a Class A audio power amplifier (one channel per PCB, front end only). See http://www.firstwatt.com/pdf/art_a40.pdf and http://www.firstwatt.com/pdf/art_a40_redux.pdf for details.
ColecoRGB PAL
author: citrus3000psi
2 layer board of 2.19 x 0.71 inches (55.6 x 18.0 mm)
Uploaded:
December 28, 2017
Shared:
March 05, 2018
Total Price:
$7.70
Untested, use at own risk.
All components are 0603, unless stated differently.
C1, C2, C3, C6, C7, C10, C11 = .1u
C4, C5, C8, C9 = 47u - 0805/10v | 478-8652-1-ND
C12 = .01u
R1, R2, R3 = 75
R4 = 82
R5 = 680
R6, R9, R10, R12, R15, R16, R19, R21, R22, R23, R24, R28 = 1K
R7…
Show full description
Untested, use at own risk.
All components are 0603, unless stated differently.
C1, C2, C3, C6, C7, C10, C11 = .1u
C4, C5, C8, C9 = 47u - 0805/10v | 478-8652-1-ND
C12 = .01u
R1, R2, R3 = 75
R4 = 82
R5 = 680
R6, R9, R10, R12, R15, R16, R19, R21, R22, R23, R24, R28 = 1K
R7…
Show full description
led_module.kicad_pcb
author: marsairforce
4 layer board of 0.40 x 1.16 inches (10.1 x 29.4 mm)
Uploaded:
April 06, 2017
Shared:
March 04, 2018
Total Price:
$4.50
2.1 led breadboard module
2.1 led breadboard module
charge_pump.kicad_pcb
author: marsairforce
2 layer board of 0.68 x 0.41 inches (17.4 x 10.4 mm)
Uploaded:
May 25, 2017
Shared:
March 04, 2018
Total Price:
$1.35
level_shifter.kicad_pcb
author: marsairforce
2 layer board of 0.43 x 0.37 inches (10.8 x 9.3 mm)
Uploaded:
May 29, 2017
Shared:
March 04, 2018
Total Price:
$0.75
hex_display.kicad_pcb
author: marsairforce
4 layer board of 1.61 x 1.11 inches (40.8 x 28.1 mm)
Uploaded:
March 04, 2018
Shared:
March 04, 2018
Total Price:
$17.70
A 28 DIP footprint module to hold 4 segment displays. I use an Atmega 164 as the logic, because of the small space from single part, and the inexpensiveness and simplicity of it to use.
A 28 DIP footprint module to hold 4 segment displays. I use an Atmega 164 as the logic, because of the small space from single part, and the inexpensiveness and simplicity of it to use.
