Mega Drive++ R
author: pcm720
2 layer board of 1.28 x 0.77 inches (32.6 x 19.5 mm)
Uploaded:
October 17, 2018
Shared:
January 24, 2019
Total Price:
$4.90
Source code and KiCAD project repository
Sega Mega Drive/Genesis modchip design heavily inspired by MegaDrive++ project. Layout optimized for Model 2 VA1 board with [dual frequency oscillator](https://oshpar…
Show full description
Source code and KiCAD project repository
Sega Mega Drive/Genesis modchip design heavily inspired by MegaDrive++ project. Layout optimized for Model 2 VA1 board with [dual frequency oscillator](https://oshpar…
Show full description
fat_power.kicad_pcb
author: citrus3000psi
2 layer board of 2.12 x 1.29 inches (53.7 x 32.7 mm)
Uploaded:
January 05, 2019
Shared:
January 24, 2019
Total Price:
$13.60
hv_relay_array
author: mrswirlyeyes
2 layer board of 1.44 x 0.72 inches (36.5 x 18.3 mm)
Uploaded:
January 23, 2019
Shared:
January 24, 2019
Total Price:
$5.15
Rev 1
Rev 1
full_stack_test_brd
author: mrswirlyeyes
2 layer board of 1.62 x 1.24 inches (41.0 x 31.5 mm)
Uploaded:
January 24, 2019
Shared:
January 24, 2019
Total Price:
$10.00
Rev 1
Rev 1
ATtiny841 Breakout
author: Aerospacesmith
2 layer board of 0.73 x 1.08 inches (18.5 x 27.5 mm)
Uploaded:
January 24, 2019
Shared:
January 24, 2019
Total Price:
$3.95
Minimal breakout for ATtiny841. Has reset button, ICSP port, and 3.3V regulator to accept 3.9V - 9V supply. Uses the calibrated internal 8MHz oscillator which is ±2% when Vcc is <4V (this breakout regulates to 3.3V).
Minimal breakout for ATtiny841. Has reset button, ICSP port, and 3.3V regulator to accept 3.9V - 9V supply. Uses the calibrated internal 8MHz oscillator which is ±2% when Vcc is <4V (this breakout regulates to 3.3V).
A better battery board for Wearables
author: Lazerade
2 layer board of 1.21 x 1.21 inches (30.7 x 30.7 mm)
Uploaded:
November 25, 2018
Shared:
January 23, 2019
Total Price:
$7.25
This board works with any single Lipo battery. I've used them with flat and coin cell type batteries.
(BOM coming soon…)
This board works with any single Lipo battery. I've used them with flat and coin cell type batteries.
(BOM coming soon…)
CC6_power_supply_breakout
author: nTrfAce
2 layer board of 1.50 x 1.50 inches (38.1 x 38.1 mm)
Uploaded:
January 23, 2019
Shared:
January 23, 2019
Total Price:
$11.25
microUSB 5V in, CC6-0503SR-E 6W power supply module, 3.3V at 1.8A out. Mounting holes for M2.5 standoffs and hardware.
microUSB 5V in, CC6-0503SR-E 6W power supply module, 3.3V at 1.8A out. Mounting holes for M2.5 standoffs and hardware.
PCE Avenue 3-button controller board
author: skum
2 layer board of 2.11 x 1.64 inches (53.7 x 41.7 mm)
Uploaded:
January 23, 2019
Shared:
January 23, 2019
Total Price:
$17.30
Completely untested! Based on this: http://www.webalice.it/cicciopetito/archivio/Avenue_Pad_3_Schematic.png
Completely untested! Based on this: http://www.webalice.it/cicciopetito/archivio/Avenue_Pad_3_Schematic.png
Talon SRX Breakout v2[tested]
author: james
2 layer board of 1.01 x 0.96 inches (25.6 x 24.3 mm)
Uploaded:
January 23, 2019
Shared:
January 23, 2019
Total Price:
$4.80
Breakout board for TalonSRX Motor Controller. Includes optional 0805 resistor (10K) and 0805 schotkky diode pads to support 5V -> 3V level shifting for 5V encoder signals on rev 1.5 and earlier versions (2015 production run) of the motor controller (per the CTRE data sheet Electrical/Mechanical s…
Show full description
Breakout board for TalonSRX Motor Controller. Includes optional 0805 resistor (10K) and 0805 schotkky diode pads to support 5V -> 3V level shifting for 5V encoder signals on rev 1.5 and earlier versions (2015 production run) of the motor controller (per the CTRE data sheet Electrical/Mechanical s…
Show full description
TLV2361_breakout
author: mrswirlyeyes
2 layer board of 0.62 x 0.62 inches (15.7 x 15.6 mm)
Uploaded:
January 23, 2019
Shared:
January 23, 2019
Total Price:
$1.90
Rev 1
Rev 1
drv8662_breakout
author: mrswirlyeyes
2 layer board of 0.82 x 0.72 inches (20.8 x 18.2 mm)
Uploaded:
January 23, 2019
Shared:
January 23, 2019
Total Price:
$2.90
Rev 2
Rev 2
ATtiny Programmer v3
author: mbbackus
2 layer board of 1.24 x 1.60 inches (31.4 x 40.6 mm)
Uploaded:
August 18, 2018
Shared:
January 23, 2019
Total Price:
$9.90
Arduino Nano shield to make programming an ATtiny84 and an ATtiny85 quick and easy.
Change Log for ATtiny Programmer v3: - Moved the integrated circuit sockets further away from each other.
Arduino Nano shield to make programming an ATtiny84 and an ATtiny85 quick and easy.
Change Log for ATtiny Programmer v3: - Moved the integrated circuit sockets further away from each other.
f99_pwm_board
author: Telanoc
2 layer board of 0.71 x 0.35 inches (18.0 x 8.8 mm)
Uploaded:
January 22, 2019
Shared:
January 22, 2019
Total Price:
$1.20
Stupid little board to allow a Sunon MF40100V1-1000U-F99 fan, which has a good/fail output, to replace a -G99 type, which has a tachometer output. The ATTiny looks for the fan's pin to be low, and if it's low it sends pulses back to the Einsy. Why? Because I have some -F99 fans but want to put…
Show full description
Stupid little board to allow a Sunon MF40100V1-1000U-F99 fan, which has a good/fail output, to replace a -G99 type, which has a tachometer output. The ATTiny looks for the fan's pin to be low, and if it's low it sends pulses back to the Einsy. Why? Because I have some -F99 fans but want to put…
Show full description
Duplicator i3 Plus Interface Board
author: ryanpriore
2 layer board of 1.45 x 0.99 inches (36.8 x 25.2 mm)
Uploaded:
January 22, 2019
Shared:
January 22, 2019
Total Price:
$7.15
This is an Interface Plate Keypin compatible on the Duplicator i3 Plus, the Maker Select Plus, and similar clones.
This is an Interface Plate Keypin compatible on the Duplicator i3 Plus, the Maker Select Plus, and similar clones.
