Raspberry Pi CM3 carrier board
author: dimonic
4 layer board of 3.68 x 2.46 inches (93.4 x 62.6 mm)
Uploaded:
February 01, 2019
Shared:
February 01, 2019
Total Price:
$90.50
Provides usual Pi functionality and pinouts for the Compute Module 3.
Provides usual Pi functionality and pinouts for the Compute Module 3.
VoltageReferenceTest-ammended-for-10V
author: alexsh1
2 layer board of 2.93 x 1.25 inches (74.3 x 31.8 mm)
Uploaded:
February 01, 2019
Shared:
February 01, 2019
Total Price:
$18.30
https://www.barbouri.com/2016/07/23/programmable-voltage-reference-v2-12-completion/
https://www.barbouri.com/2016/07/23/programmable-voltage-reference-v2-12-completion/
New folder (2)
author: cheetahgod
2 layer board of 1.01 x 2.21 inches (25.6 x 56.0 mm)
Uploaded:
January 31, 2019
Shared:
February 01, 2019
Total Price:
$11.05
PWM LCD
author: jasonaaronfox
2 layer board of 1.71 x 1.43 inches (43.5 x 36.2 mm)
Uploaded:
September 02, 2013
Shared:
February 01, 2019
Total Price:
$12.15
Final design
Final design
bergstak_mezzanine_breakout
author: buckd
4 layer board of 1.80 x 1.99 inches (45.8 x 50.4 mm)
Uploaded:
January 07, 2019
Shared:
February 01, 2019
Total Price:
$35.70
2x50 FCI BergStak breakout. Useful for MicroZed testing. 4-layer board is used for better shielding, thicker traces, and reduced footprint.
Fully flip-able and can be used as a pass-thru breakout.
Parts: * 100-pin BergStak FMC connector. BOM 61082-101400LF or its mate 61083-101400L…
Show full description
2x50 FCI BergStak breakout. Useful for MicroZed testing. 4-layer board is used for better shielding, thicker traces, and reduced footprint.
Fully flip-able and can be used as a pass-thru breakout.
Parts: * 100-pin BergStak FMC connector. BOM 61082-101400LF or its mate 61083-101400L…
Show full description
new_holder_board_fixed
author: cltschirhart
2 layer board of 0.95 x 0.77 inches (24.0 x 19.5 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$3.60
new_sample_board_fixed
author: cltschirhart
2 layer board of 0.95 x 0.79 inches (24.0 x 20.0 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$3.70
traynor_power_supply.kicad_pcb
author: marsairforce
2 layer board of 4.02 x 1.88 inches (102.2 x 47.6 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$37.70
The power supply for a Traynor YGA1 guitar tube amplifier. The one I had was built around 1966. The original capacitors are likely no good anymore. And the point to point "ladder" circuit on cardboard like material with brass eyelets seems a lot unsafe by today's standards. Schematic: https://e…
Show full description
The power supply for a Traynor YGA1 guitar tube amplifier. The one I had was built around 1966. The original capacitors are likely no good anymore. And the point to point "ladder" circuit on cardboard like material with brass eyelets seems a lot unsafe by today's standards. Schematic: https://e…
Show full description
double_shot.kicad_pcb
author: robertlong13
2 layer board of 1.11 x 1.26 inches (28.1 x 31.9 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$6.90
Time Sleuth 1.1
author: citrus3000psi
2 layer board of 2.84 x 1.70 inches (72.2 x 43.2 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$24.15
See more details here: https://github.com/citrus3000psi/Time-Sleuth
See more details here: https://github.com/citrus3000psi/Time-Sleuth
Beastie Pass Band Filter (200-800MHz)
author: jdc_idlab
2 layer board of 1.69 x 0.47 inches (43.0 x 12.0 mm)
Uploaded:
January 30, 2019
Shared:
January 31, 2019
Total Price:
$3.95
Pass Band Filter that is simulated to be around 200-800MHz BW with assuming load of 50
Note : not tested yet.
Pass Band Filter that is simulated to be around 200-800MHz BW with assuming load of 50
Note : not tested yet.
OMSI - LED Wall - RS485 Receiver Board
author: hydronics
2 layer board of 2.71 x 4.18 inches (68.8 x 106.2 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$56.60
This board receives RS485 signals via RJ485 ethernet jack. Converts the two differential pairs back into clock and data SPI signals for one LED panel. The board also has a DC-to-DC converter that takes 45V to 5V to supply to the LED panel.
Trnsceiver Chip: SP485EN, 1016-1829-1-ND RJ45 Ethern…
Show full description
This board receives RS485 signals via RJ485 ethernet jack. Converts the two differential pairs back into clock and data SPI signals for one LED panel. The board also has a DC-to-DC converter that takes 45V to 5V to supply to the LED panel.
Trnsceiver Chip: SP485EN, 1016-1829-1-ND RJ45 Ethern…
Show full description
OMSI - LED Wall - Mojo Shield
author: hydronics
2 layer board of 3.95 x 3.44 inches (100.3 x 87.3 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$67.90
This simple shield connects to the Mojo FPGA development board and breaks out all the pins to 5.08mm phoenix connectors. The HDMI shield fits on the Mojo and this shield connects ontop of the HDMI shield.
Mojo Development Board: https://alchitry.com/products/mojo-v3 HDMI Shield: https://alch…
Show full description
This simple shield connects to the Mojo FPGA development board and breaks out all the pins to 5.08mm phoenix connectors. The HDMI shield fits on the Mojo and this shield connects ontop of the HDMI shield.
Mojo Development Board: https://alchitry.com/products/mojo-v3 HDMI Shield: https://alch…
Show full description
OMSI - LED Wall - RS485 Transmitter Board
author: hydronics
2 layer board of 2.56 x 1.16 inches (65.1 x 29.5 mm)
Uploaded:
January 31, 2019
Shared:
January 31, 2019
Total Price:
$14.90
This is a simple board that takes two SPI signals (Clock and Data), passes the signals through a RS485 transmitter chip. The differential signals are routed to an ethernet jack.
transmitter chip: Texas Instrument AM27LV31 296-24690-1-ND RJ45 ethernet jack: 380-1316-5-ND
https://github.com/…
Show full description
This is a simple board that takes two SPI signals (Clock and Data), passes the signals through a RS485 transmitter chip. The differential signals are routed to an ethernet jack.
transmitter chip: Texas Instrument AM27LV31 296-24690-1-ND RJ45 ethernet jack: 380-1316-5-ND
https://github.com/…
Show full description
HC12-Ser-Select
author: Jarrett
2 layer board of 0.71 x 0.98 inches (18.0 x 24.9 mm)
Uploaded:
January 30, 2019
Shared:
January 30, 2019
Total Price:
$3.45
Switch between RS232 and a standard USB-UART adaptor for the Adapt912 series of 68HC12 microcontroller dev board
Switch between RS232 and a standard USB-UART adaptor for the Adapt912 series of 68HC12 microcontroller dev board
ResBrd
author: IRDPHOENIX
2 layer board of 2.01 x 2.11 inches (51.0 x 53.5 mm)
Uploaded:
June 17, 2016
Shared:
January 30, 2019
Total Price:
$21.10
Resistor Board
Resistor Board
Voltage divider v0.1
author: Pawelsky
2 layer board of 0.35 x 0.25 inches (8.9 x 6.4 mm)
Uploaded:
August 17, 2014
Shared:
January 30, 2019
Total Price:
$0.40
Just a tiny voltage divider board
![Divider PCB](https://static.rcgroups.net/forums/attachments/3/9/3/9/3/6/a7064425-25-voltage_divider.jpg%20"Divider%20PCB")
![Divider connection](https://static.rcgroups.net/forums/attachments/3/9/3/9/3/6/a7081585-228-divider_connection_diagram.jpg "Divider co…
Show full description
Just a tiny voltage divider board
![Divider connection](https://static.rcgroups.net/forums/attachments/3/9/3/9/3/6/a7081585-228-divider_connection_diagram.jpg "Divider co…
Show full description
