Breadboard connector for RFM69CW (and other HopeRF radios) with 3v3 power supply, FTDI connection and breakout for all RFM signals. It uses FlexyPins by SolderParty to the radio can be tested without soldering it to the board.

The ItsyBitsy Breadboard Adapter is an Adafruit ItsyBitsy M4 Express-compatible piggyback module that converts the 3-sided pinout of the ItsyBitsy to dual in-line for use on typical solderless breadboards and soldered protoboards. The adapter was also designed with extra solderable pin connections and mounting ears for permanent installation.

Included is a STEMMA-QT connector that can be optionally configured to connect to the ItsyBitsy’s UART (RX/TX) or I2C (SCL/SDA) signals. A 2-pin JST LiPo battery connection is on-board that supports charging (100mA charge rate), compatible with Adafruit’s standard battery connector polarity.

this is a board that will let you press up to 4 different inputs at once with one button. ideally used with gameboy games that reset with the command st+se+a+b

uses FMN1T148

Power distribution board for ant/beetle weight combat robots. Uses through-hole XT30 connectors, a 3mm LED, a surface mount resistor, and a FingerTech power switch.

Power distribution board for ant/beetle weight combat robots. Uses through-hole XT30 connectors, a 3mm LED, a surface mount resistor, and a FingerTech power switch.

Credit: https://www.youtube.com/redirect?event=video_description&redir_token=QUFFLUhqbXRpSkhHNnUyMWxjYTJRVkI0b3EtcjZuUDFNZ3xBQ3Jtc0tsWXJPZ0VoZXVfZi1jNjJYeC1EN1ZOR1RKNFdTOG5yM0ZyVGg1aUx5Um5LYkJzVWtfZkJiNlVRdmdFZU03YWlHb25iR1cxRXd6aVlyNlFJN0dWblVETjg0WUNtbGc0bm1GRU9fbjdRMXA2SV94dDQ5WQ&q=https%3A%2F%2Fgithub.com%2FTishima%2FmyDRAMTester&v=JHucAeh6SI8

Prototyping Shield for Arduino Micro with SMD footprints SO08, SOT223 and SOT23

Have you ever been frustrated creating a prototype using a simple MOSFET or 8-pin chip that’s only available in SMD? This Micro Proto Shield is the answer, for the Arduino Micro platform.

Information on the board

All Arduino pins are labelled on both sides of the board. The Arduino symbol and the ISP header outline are provided to help you plug in the Micro the correct way around.

All wires to the SMD footprints are shown in white on the silkscreen so you can quickly see which hole connects to which SMD pad.

N-channel MOSFETS connected to PWM pins

The two large MOSFET footprints Q1 and Q2 are already connected to the first two PWM pins (3 and 5) on your Arduino. Source is connected to grounds and the Drain output has a prototyping hole connected to the large tab on the transistor.

The transistors require pulldowns to hold them in the off state while the Arduino bootloader is active. Footprints for 0805 size resistors are provided for R1 and R2. Or you can wire through-hole resistors to the pads adjacent to pins 3 and 5.

If the pinouts on your transistors are different, just cut the resolderable traces between the holes and wire them up how you want.

SOT23 footprints

The large SOT-223 transistors have enough space inside their footprint to include pads for SOT23 size transistors too: Q3 and Q4. The wiring is the same as common N-channel MOSFETS or you can cut the resolderable traces and wire it however you want.

SO-8 integrated circuit U1

This seems to be a common size for memory chips, thermocouple interfaces and a lot of other different chips. All 8 pins are broken out to holes, with no default wiring. Connect your chip any way you want.

95 free prototyping holes

There’s still a large number of free holes on the board, so a 14-pin DIL chip can be installed or anything else that fits. +5V, +3.3V and ground buses are provided at both ends of the board.

Check out the standard prototyping version too

I’ve also shared a version without the SMD footprints, if you need more conventional components.

Uses MX28F2000 to hold 3 or 4 games. The games are selectable with dip switches.

LED driver board that plugs into a Pico. Constant current buck using LM3405 and has STEMMA QT connector.