74xxx TSSOP to DIP converter
author: amiga.technology
2 layer board of 0.41 x 0.74 inches (10.3 x 18.7 mm)
Uploaded:
April 19, 2023
Shared:
April 19, 2023
Total Price:
$1.45
Can't find that 74xxx part in DIP-14 but there's a TSSOP-14 available? This little adapter will help you. It connects the pins 1:1.
This hardware is released under Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0)
Can't find that 74xxx part in DIP-14 but there's a TSSOP-14 available? This little adapter will help you. It connects the pins 1:1.
This hardware is released under Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0)
7408 TSSOP to DIP converter
author: amiga.technology
2 layer board of 0.41 x 0.74 inches (10.3 x 18.7 mm)
Uploaded:
April 19, 2023
Shared:
April 19, 2023
Total Price:
$1.45
Want to use a 74ABT08 in a DIP14 form factor?
Want to use a 74ABT08 in a DIP14 form factor?
LB1836 v1
author: tseary
2 layer board of 0.68 x 0.50 inches (17.3 x 12.7 mm)
Uploaded:
November 15, 2022
Shared:
April 18, 2023
Total Price:
$1.70
Compact carrier board for LB1836 low voltage DC motor driver, frequently used in Lego products at 4.5 V or 9 V.
Components: 1x LB1836 chip (1 mm pitch) 1x 350 mA 1206 PTC fuse 2x 0.1 uF 0603 capacitor 1x 47 uF 6.3 mm electrolytic capacitor (optional)
This motor driver can control two DC motors …
Show full description
Compact carrier board for LB1836 low voltage DC motor driver, frequently used in Lego products at 4.5 V or 9 V.
Components: 1x LB1836 chip (1 mm pitch) 1x 350 mA 1206 PTC fuse 2x 0.1 uF 0603 capacitor 1x 47 uF 6.3 mm electrolytic capacitor (optional)
This motor driver can control two DC motors …
Show full description
Sewable Neopixel
author: tseary
2 layer board of 1.06 x 1.06 inches (26.9 x 26.9 mm)
Uploaded:
December 01, 2022
Shared:
April 18, 2023
Total Price:
$5.60
A low-cost sewable addressable RGB, for those who don't mind SMT soldering.
Components: 1x WS2812B LED 2x 22 Ohm 0603 resistors 1x 0.1 uF 0603 capacitor
This board is a mini panel of four, so each order contains 12 dots.
A low-cost sewable addressable RGB, for those who don't mind SMT soldering.
Components: 1x WS2812B LED 2x 22 Ohm 0603 resistors 1x 0.1 uF 0603 capacitor
This board is a mini panel of four, so each order contains 12 dots.
Beeper.kicad_pcb
author: AnalogGuy
2 layer board of 1.57 x 0.98 inches (40.0 x 25.0 mm)
Uploaded:
April 15, 2023
Shared:
April 18, 2023
Total Price:
$7.70
This is a battery powered test fixture which converts the voltage or impedance seen at its inputs to an audible tone, about 200Hz to 1.6kHz. Power comes from three AAA batteries, and the unit turns itself off an on automatically. Power consumption in standby is TBDµA, and when making a 200Hz tone…
Show full description
This is a battery powered test fixture which converts the voltage or impedance seen at its inputs to an audible tone, about 200Hz to 1.6kHz. Power comes from three AAA batteries, and the unit turns itself off an on automatically. Power consumption in standby is TBDµA, and when making a 200Hz tone…
Show full description
Arduino Pro Micro ICSP shield 1.0
author: Hanyazou
2 layer board of 1.30 x 0.70 inches (33.0 x 17.8 mm)
Uploaded:
March 18, 2023
Shared:
April 17, 2023
Total Price:
$4.50
PIC 18F programmer shield for Arduino pro micro. You can find FW and programmer at the github. https://github.com/hanyazou/a-p-prog
PIC 18F programmer shield for Arduino pro micro. You can find FW and programmer at the github. https://github.com/hanyazou/a-p-prog
H503-0.1
author: Bear_Metal
4 layer board of 2.00 x 0.80 inches (50.8 x 20.4 mm)
Uploaded:
April 02, 2023
Shared:
April 17, 2023
Total Price:
$16.00
This is a small board to experiment with the STM32H503, a 250 MHz ARM Cortex-M33. The board will fit into a Arduino Nano socket, though it is only partially compatible with the Nano pinout. The KiCad project, BOM, and firmware are on GitHub. The firmware consists of a small command-line interpret…
Show full description
This is a small board to experiment with the STM32H503, a 250 MHz ARM Cortex-M33. The board will fit into a Arduino Nano socket, though it is only partially compatible with the Nano pinout. The KiCad project, BOM, and firmware are on GitHub. The firmware consists of a small command-line interpret…
Show full description
Nintendo OEM SNES Controller Replacement PCB - rev_5j
author: Taylor-MadeAK
2 layer board of 4.96 x 1.77 inches (126.0 x 45.0 mm)
Uploaded:
April 15, 2023
Shared:
April 16, 2023
Total Price:
$43.90
This is a replacement PCB for SNES controllers using readily available off-the-shelf parts with a focus on being hand-soldering friendly.
Features:
Works just like the original, but better protected against ESD damage.
OPTIONAL LEDs!
OPTIONAL SOCD filter circuit for D-pad input.
Asse…
Show full description
This is a replacement PCB for SNES controllers using readily available off-the-shelf parts with a focus on being hand-soldering friendly.
Features:
Works just like the original, but better protected against ESD damage.
OPTIONAL LEDs!
OPTIONAL SOCD filter circuit for D-pad input.
Asse…
Show full description
RFM69_FlexyPin_Shield_0-E_2023-02-14
author: brandock
2 layer board of 2.05 x 1.25 inches (52.2 x 31.8 mm)
Uploaded:
February 14, 2023
Shared:
April 15, 2023
Total Price:
$12.85
A breakout for RFM69CW HopeRF radios designed as a shield for Arduino Uno. It is notoriously difficult to connect HopeRF radios, which are 3v3 devices, to Arduino, which are 5V devices. The 47uF and .1uF capacitors in this design have worked for me.
A breakout for RFM69CW HopeRF radios designed as a shield for Arduino Uno. It is notoriously difficult to connect HopeRF radios, which are 3v3 devices, to Arduino, which are 5V devices. The 47uF and .1uF capacitors in this design have worked for me.
WetSensorHeated
author: NASA-AERONET
2 layer board of 0.63 x 1.52 inches (16.0 x 38.7 mm)
Uploaded:
April 13, 2023
Shared:
April 13, 2023
Total Price:
$4.75
AD8232_ModFinal
author: laughingman
2 layer board of 1.24 x 1.31 inches (31.5 x 33.2 mm)
Uploaded:
April 13, 2023
Shared:
April 13, 2023
Total Price:
$8.05
