LND150 CCS
author: Peef
2 layer board of 0.60 x 0.29 inches (15.2 x 7.3 mm)
Uploaded:
July 15, 2023
Shared:
July 15, 2023
Total Price:
$0.85
A daughterboard suitable for replacing a 1/4W resistor with a CCS. The board is designed to accept the LND150 in TO92 or SOT23 and can be used with other pin-compatible parts, such as certain JFETs. There are spots for both a source resistor and gate stopper.
A daughterboard suitable for replacing a 1/4W resistor with a CCS. The board is designed to accept the LND150 in TO92 or SOT23 and can be used with other pin-compatible parts, such as certain JFETs. There are spots for both a source resistor and gate stopper.
RGBS AMP + Audio 1in/2out
author: The_Real_Phoenix
2 layer board of 2.35 x 1.70 inches (59.7 x 43.2 mm)
Uploaded:
July 15, 2023
Shared:
July 15, 2023
Total Price:
$19.95
Screw terminals can be https://www.digikey.ca/en/products/detail/phoenix-contact/1751264/2511021 but any 3.50 spacing ones should be good I'd like to test https://www.digikey.ca/en/products/detail/adam-tech/EBWA-04-A/9830530 which are cheaper
I put the ref for the trimpots in back https://www.d…
Show full description
Screw terminals can be https://www.digikey.ca/en/products/detail/phoenix-contact/1751264/2511021 but any 3.50 spacing ones should be good I'd like to test https://www.digikey.ca/en/products/detail/adam-tech/EBWA-04-A/9830530 which are cheaper
I put the ref for the trimpots in back https://www.d…
Show full description
PICSARR - DD PCB.kicad_pcb
author: Dr_Eileen_Meyer
2 layer board of 2.62 x 2.78 inches (66.6 x 70.6 mm)
Uploaded:
July 13, 2023
Shared:
July 13, 2023
Total Price:
$36.40
SPRITE board version 1.0. Designed by Nathan Wong.
SPRITE board version 1.0. Designed by Nathan Wong.
AHRS_01
author: austen.clair
2 layer board of 1.34 x 1.60 inches (33.9 x 40.7 mm)
Uploaded:
July 12, 2023
Shared:
July 12, 2023
Total Price:
$10.70
BMS_A
author: austen.clair
2 layer board of 2.27 x 2.22 inches (57.8 x 56.5 mm)
Uploaded:
July 11, 2023
Shared:
July 11, 2023
Total Price:
$25.25
type-type-board
author: mlupo
2 layer board of 1.77 x 2.36 inches (44.9 x 59.9 mm)
Uploaded:
June 20, 2023
Shared:
July 11, 2023
Total Price:
$20.85
This project uses an Adafruit KB2040 board to send parallel data to an electronic typewriter via its Centronics port (using a DB-25 to Centronics cable).
Keep in mind that I am artist who codes by mistake….your mileage may vary.
This project uses an Adafruit KB2040 board to send parallel data to an electronic typewriter via its Centronics port (using a DB-25 to Centronics cable).
Keep in mind that I am artist who codes by mistake….your mileage may vary.
BME280 tiny breakout
author: MalteP
2 layer board of 0.30 x 0.79 inches (7.7 x 20.2 mm)
Uploaded:
June 24, 2023
Shared:
July 09, 2023
Total Price:
$1.15
Small breakout board which fits into Aliexpress protective sensor cases. Pads can be soldered to the cable directly. 3,3V only (no onboard LDO or level-shifter). May be used with BME280 (temperature, barometric pressure, humidity), BMP280 or SPL06 (temperature & pressure only).
Photo: [https://…
Show full description
Small breakout board which fits into Aliexpress protective sensor cases. Pads can be soldered to the cable directly. 3,3V only (no onboard LDO or level-shifter). May be used with BME280 (temperature, barometric pressure, humidity), BMP280 or SPL06 (temperature & pressure only).
Photo: [https://…
Show full description
LTC4054.kicad_pcb
author: shermluge
2 layer board of 0.64 x 0.47 inches (16.3 x 11.9 mm)
Uploaded:
June 29, 2023
Shared:
July 08, 2023
Total Price:
$1.45
Low current Lipo battery charger (best with small solar panel).
https://www.shermluge.com/electronics/attiny-202402/attiny402-firefly-remake-of-attiny85-firefly
Low current Lipo battery charger (best with small solar panel).
https://www.shermluge.com/electronics/attiny-202402/attiny402-firefly-remake-of-attiny85-firefly
Stlink-V3MINIE_adapter
author: daehyeok
2 layer board of 0.52 x 0.41 inches (13.3 x 10.5 mm)
Uploaded:
July 05, 2023
Shared:
July 07, 2023
Total Price:
$1.05
board-to-board adapter to use Stlink-V3MINIE with standard 2.54mm pitch pin connectors. It required Kyocera BTB connector(009159010061911) and 2x05 2.54mm pitch pin headers.
board-to-board adapter to use Stlink-V3MINIE with standard 2.54mm pitch pin connectors. It required Kyocera BTB connector(009159010061911) and 2x05 2.54mm pitch pin headers.
