BED Backpack v1.1
author: EmbeddedMan
2 layer board of 4.01 x 2.51 inches (101.9 x 63.8 mm)
Uploaded:
November 16, 2013
Shared:
November 16, 2013
Total Price:
$50.30
Big Easy Driver quad carrier board, v1.1 See http://schmalzhaus.com/BigEasyDriver/BEDBackpackV11.zip for complete information.
Big Easy Driver quad carrier board, v1.1 See http://schmalzhaus.com/BigEasyDriver/BEDBackpackV11.zip for complete information.
UV5R TRRS Adapter
author: chrishood
2 layer board of 1.08 x 0.32 inches (27.4 x 8.2 mm)
Uploaded:
November 13, 2013
Shared:
November 13, 2013
Total Price:
$1.70
Almost an exact duplicate of the original, all I did was change the ground to a ground plane on the bottom of the board, to hopefully help with some signal shielding. Please see the original at https://github.com/johnboiles/BaofengUV5R-TRRS. Thank you John.
BOM:
1x 3.5mm Stereo Cable
…
Show full description
Almost an exact duplicate of the original, all I did was change the ground to a ground plane on the bottom of the board, to hopefully help with some signal shielding. Please see the original at https://github.com/johnboiles/BaofengUV5R-TRRS. Thank you John.
BOM:
1x 3.5mm Stereo Cable
…
Show full description
Ferm Control RevC
author: LordUlrich
2 layer board of 4.12 x 1.48 inches (104.6 x 37.5 mm)
Uploaded:
October 20, 2013
Shared:
November 13, 2013
Total Price:
$30.35
Fermentation Temp Controller
Fermentation Temp Controller
LM317 Regulator Board
author: XOIIO
2 layer board of 0.72 x 1.14 inches (18.2 x 28.9 mm)
Uploaded:
November 13, 2013
Shared:
November 13, 2013
Total Price:
$4.05
A simple board to set up your LM317, use a calculator to find resistor values. C1 is .01μf, c2 can be anything but 47μf is good.
A simple board to set up your LM317, use a calculator to find resistor values. C1 is .01μf, c2 can be anything but 47μf is good.
TLC5947 Breakout
author: JordiOrlando
2 layer board of 0.50 x 1.60 inches (12.7 x 40.6 mm)
Uploaded:
November 13, 2013
Shared:
November 13, 2013
Total Price:
$4.00
QFN
QFN
EasyRider
author: stamina
2 layer board of 4.73 x 2.96 inches (120.2 x 75.2 mm)
Uploaded:
November 12, 2013
Shared:
November 12, 2013
Total Price:
$69.95
Motorcycle control & telemetrics
This is rev B of the original project located here: https://github.com/stamina/easyrider
Now with mostly SMD parts, GPS and WIFI.
Motorcycle control & telemetrics
This is rev B of the original project located here: https://github.com/stamina/easyrider
Now with mostly SMD parts, GPS and WIFI.
USB IDevice charger V2
author: Erll
2 layer board of 2.20 x 1.56 inches (55.9 x 39.6 mm)
Uploaded:
November 11, 2013
Shared:
November 11, 2013
Total Price:
$17.10
USB Charger V2 using OnSemi lm2576 switching regulator. It will provide 5v 3amp output for charging I devices. There are resistor dividers for making the correct voltages on the d+ and d- . This layout is untested, but the schematic is fully tested and works well. There is one error on this board…
Show full description
USB Charger V2 using OnSemi lm2576 switching regulator. It will provide 5v 3amp output for charging I devices. There are resistor dividers for making the correct voltages on the d+ and d- . This layout is untested, but the schematic is fully tested and works well. There is one error on this board…
Show full description
Seven-segment display
author: RomainViollette
2 layer board of 2.52 x 0.86 inches (63.9 x 21.7 mm)
Uploaded:
November 11, 2013
Shared:
November 11, 2013
Total Price:
$10.75
description: Autonomous 3 seven-segments display powered by an Atmega328P.
features: - small form factor - communication: Serial, I2C, SPI, (bitbanging possible if you want to) - SDM components, soldering by hand is not too difficult. - 5 volts only - Arduino IDE compatible - progra…
Show full description
description: Autonomous 3 seven-segments display powered by an Atmega328P.
features: - small form factor - communication: Serial, I2C, SPI, (bitbanging possible if you want to) - SDM components, soldering by hand is not too difficult. - 5 volts only - Arduino IDE compatible - progra…
Show full description
