shaft encoder splitter/isolator
author: KD7MRX
2 layer board of 2.00 x 2.00 inches (50.8 x 50.8 mm)
Uploaded:
December 17, 2012
Shared:
June 08, 2014
Total Price:
$19.95
send the output of a shaft encoder to two devices without creating a ground loop
send the output of a shaft encoder to two devices without creating a ground loop
Freemo Switch board
author: cstalsworth
2 layer board of 1.33 x 0.72 inches (33.8 x 18.2 mm)
Uploaded:
June 08, 2014
Shared:
June 08, 2014
Total Price:
$4.75
Wire board for switch control on module
Wire board for switch control on module
Quadcopter Power Distribution Board kit
author: gcardinal
2 layer board of 2.02 x 2.02 inches (51.2 x 51.2 mm)
Uploaded:
November 06, 2013
Shared:
June 07, 2014
Total Price:
$20.30
This quadcopter PDB can be used with any frame. It distributes power from the flight battery to ESCs to power the Quad's motors.
This quadcopter PDB can be used with any frame. It distributes power from the flight battery to ESCs to power the Quad's motors.
SO2Rduino V2
author: goboxgizmos
2 layer board of 6.30 x 2.62 inches (160.0 x 66.5 mm)
Uploaded:
September 24, 2013
Shared:
June 07, 2014
Total Price:
$82.45
Solar Battery Charger
author: goboxgizmos
2 layer board of 2.55 x 0.79 inches (64.8 x 20.0 mm)
Uploaded:
September 24, 2013
Shared:
June 07, 2014
Total Price:
$10.00
Simple Solar Regulator
author: goboxgizmos
2 layer board of 4.40 x 1.09 inches (111.8 x 27.6 mm)
Uploaded:
September 24, 2013
Shared:
June 07, 2014
Total Price:
$23.90
Pinguino hlak v0.5
author: goboxgizmos
2 layer board of 3.63 x 1.51 inches (92.1 x 38.4 mm)
Uploaded:
February 10, 2014
Shared:
June 07, 2014
Total Price:
$27.40
Automatic Mobile Power Control
2 layer board of 2.15 x 2.01 inches (54.7 x 51.1 mm)
Uploaded:
June 07, 2014
Shared:
June 07, 2014
Total Price:
$21.65
November 2012 QST Page 43 W8WKE.
JP1 should be disconnected unless you want the regulators to run 24/7 Connect REG_VIN to the output of the relay.
8-24-14 I specked the wrong op amp It only went to +7V on V+. change to op-amp LT6020HMS8#PBF-ND. Questions, contact me at [email protected]
BO…
Show full description
November 2012 QST Page 43 W8WKE.
JP1 should be disconnected unless you want the regulators to run 24/7 Connect REG_VIN to the output of the relay.
8-24-14 I specked the wrong op amp It only went to +7V on V+. change to op-amp LT6020HMS8#PBF-ND. Questions, contact me at [email protected]
BO…
Show full description
Db 9 Breakout
2 layer board of 0.88 x 1.68 inches (22.4 x 42.7 mm)
Uploaded:
June 07, 2014
Shared:
June 07, 2014
Total Price:
$7.40
A breakout board to take signals from a DB-9 output on my LED driver board. Has a status LED to indicate recieving power.
A breakout board to take signals from a DB-9 output on my LED driver board. Has a status LED to indicate recieving power.
Aquarium Led Driver
2 layer board of 3.73 x 2.32 inches (94.8 x 58.8 mm)
Uploaded:
June 07, 2014
Shared:
June 07, 2014
Total Price:
$43.15
A LED driver I designed for custom aquarium reef lighting. VCC is 48V, LED dimming is controlled via PWM, outputs 6 channels of up to 1A current controlled driving and one12V rail for driving cooling fans on the LED assemblies..
A LED driver I designed for custom aquarium reef lighting. VCC is 48V, LED dimming is controlled via PWM, outputs 6 channels of up to 1A current controlled driving and one12V rail for driving cooling fans on the LED assemblies..
Output Led Rev 1
author: MakersBox
2 layer board of 0.45 x 0.45 inches (11.5 x 11.5 mm)
Uploaded:
February 03, 2014
Shared:
June 07, 2014
Total Price:
$1.00
This is the LED portion of the SnapNsew board. It provides a platform for a sewable LED/resistor with reliable connections for conductive thread through large pads.
More information at http://www.instructables.com/id/SnapNsew-An-Educational-Soft-Circuit-Platform/
or contact [email protected]
This is the LED portion of the SnapNsew board. It provides a platform for a sewable LED/resistor with reliable connections for conductive thread through large pads.
More information at http://www.instructables.com/id/SnapNsew-An-Educational-Soft-Circuit-Platform/
or contact [email protected]
