OSHPARK
  • About Us
  • Services
  • Support
  • Sharing
  • Log in
  • Sign up
  • OSHPARK
  • About Us
  • Services
  • Support
  • Sharing
  • Log in

Zipit Z2 Breakout v2.0

author: mozzwald
Top
Bottom

2 layer board of 2.96 x 0.66 inches (75.1 x 16.7 mm)
Uploaded: July 21, 2016
Shared: August 01, 2016
Total Price: $9.70

Zipit Z2 Breakout v2

Parts List

  • C1, C2: 4.7uF 6.3V 0603 (C1608X5R0J475K080AB)
  • L1: 1uH 0805 (LQM21PN1R0MC0D)
  • U1: TI 5V Regulator (TPS61240DRVT)
  • J1: Hirose to Zipit Connector (ST60X-36S(30))
  • J2: USB Host Port (292303-1)
  • J3: Amphenol FCI Micro USB Port (10118194-0001LF)
  • R1: 10K ohm 0603 Resistors (Regulator Enable)
  • R2, R3: 4.7k-10k ohm 0603 Resistors (I2C)
  • 1.27mm Headers

Details

Both USB Ports are designed to be optionally broke off the middle section. Score the board with a blade on both sides down the line of holes and snap off the end. Each board when broken off can be used independently.

Main Zipit Board

This section of board contains the Hirose 36 pin connector, 1.27mm pitch headers, I2C resistors and “USB Jumpers”. The USB Jumpers allow connecting either the Micro USB (for device mode) or USB A (for host mode) port to the USB pins on the Zipit. The center pad of the jumper is connected to the Zipit. Bridge the center pad to the left or right pad with solder to set Host or Device mode.

USB-A Board

This section of board contains a USB A Port, 3.3V to 5V boost regulator, 1.27mm pitch header and jumper pads for the regulator and host power. When attached to the main Zipit board the “Host Pwr” Jumper sets which power is supplied to the port; DCIN from the Zipit or 5V from the regulator. The “Reg Jmpr” sets the regulator to be always “ON” or by toggling the “EN"able pin high (GPIO54 or via header).

Micro USB Board

This board contains a Micro USB port and 1.27mm pitch header. The VCC pin is connected to DCIN allowing you to power the Zipit via USB cable.

Zipit Z2 Breakout v2

Parts List

  • C1, C2: 4.7uF 6.3V 0603 (C1608X5R0J475K080AB)
  • L1: 1uH 0805 (LQM21PN1R0MC0D)
  • U1: TI 5V Regulator (TPS61240DRVT)
  • J1: Hirose to Zipit Connector (ST60X-36S(30))
  • J2: USB Host Port (292303-1)
  • J3: Amphenol FCI Micro USB Port (10118194-0001LF)
  • R1: 10K ohm 0603 Resistors (Regulator Enable)
  • R2, R3: 4.7k-10k ohm 0603 Resistors (I2C)
  • 1.27mm Headers

Details

Both USB Ports are designed to be optionally broke off the middle section. Score the board with a blade on both sides down the line of holes and snap off the end. Each board when broken off can be used independently.

Main Zipit Board

This section of board contains the Hirose 36 pin connector, 1.27mm pitch headers, I2C resistors and “USB Jumpers”. The USB Jumpers allow connecting either the Micro USB (for device mode) or USB A (for host mode) port to the USB pins on the Zipit. The center pad of the jumper is connected to the Zipit. Bridge the center pad to the left or right pad with solder to set Host or Device mode.

USB-A Board

This section of board contains a USB A Port, 3.3V to 5V boost regulator, 1.27mm pitch header and jumper pads for the regulator and host power. When attached to the main Zipit board the “Host Pwr” Jumper sets which power is supplied to the port; DCIN from the Zipit or 5V from the regulator. The “Reg Jmpr” sets the regulator to be always “ON” or by toggling the “EN"able pin high (GPIO54 or via header).

Micro USB Board

This board contains a Micro USB port and 1.27mm pitch header. The VCC pin is connected to DCIN allowing you to power the Zipit via USB cable.

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project
  • COMPANY
  • About Us
  • Blog
  • Shop
  • SERVICES
  • Upload Your File
  • Prototypes
  • HELP
  • Support
  • If you can't find what you're looking for, please contact us at [email protected]
  • CONNECT
  • Shared Projects
  • Log in / Sign up
Whaleshark white
Follow us
© Copyright 2025 OSH Park, LLC | Privacy