LOSA_IMU.brd
author: anilinfotek
2 layer board of 0.31 x 0.49 inches (7.9 x 12.4 mm)
Uploaded:
June 19, 2017
Shared:
June 19, 2017
Total Price:
$0.75
USB Breakout with current monitor.
author: judge2005
2 layer board of 1.76 x 0.86 inches (44.6 x 21.7 mm)
Uploaded:
May 30, 2017
Shared:
June 19, 2017
Total Price:
$7.50
This is a very simple board that allows you to tap the 5V rail of a USB connection while passing the data signals through. It also uses an INA250 to provide a current monitor so you can figure the total current draw of your projects. It sets the Is pin to 2V per amp. You can put a scope on that t…
Show full description
This is a very simple board that allows you to tap the 5V rail of a USB connection while passing the data signals through. It also uses an INA250 to provide a current monitor so you can figure the total current draw of your projects. It sets the Is pin to 2V per amp. You can put a scope on that t…
Show full description
WEMOS D1 Mini LED Shield
author: MFornander
2 layer board of 1.01 x 0.81 inches (25.6 x 20.5 mm)
Uploaded:
June 19, 2017
Shared:
June 19, 2017
Total Price:
$4.05
GPIO to LED test board
GPIO to LED test board
Raspberry Pi Power Feed HAT
author: dewhisna
2 layer board of 2.56 x 2.23 inches (64.9 x 56.7 mm)
Uploaded:
June 18, 2017
Shared:
June 18, 2017
Total Price:
$28.50
Simple Raspberry Pi HAT Board that provides the backfeed protection logic to power a Raspberry Pi board from an external +5V lab-grade power supply, as per the Raspberry Pi HAT Specs and the [ZVD Circuit](https://github.com/raspberrypi/hats/blob/master/zvd-c…
Show full description
Simple Raspberry Pi HAT Board that provides the backfeed protection logic to power a Raspberry Pi board from an external +5V lab-grade power supply, as per the Raspberry Pi HAT Specs and the [ZVD Circuit](https://github.com/raspberrypi/hats/blob/master/zvd-c…
Show full description
Analog Discovery 2 — Header adapter
author: jamescarruthers
2 layer board of 2.05 x 0.63 inches (52.1 x 15.9 mm)
Uploaded:
June 18, 2017
Shared:
June 18, 2017
Total Price:
$6.40
rc2014_6502B
author: ancientcomputing
2 layer board of 3.99 x 2.00 inches (101.3 x 50.8 mm)
Uploaded:
June 04, 2017
Shared:
June 18, 2017
Total Price:
$39.85
6502 CPU Board Rev B. Designed for the RC2014. Board design files are at <https://github.com/ancientcomputing/rc2014/tree/master/eagle/6502_board_revb>
6502 CPU Board Rev B. Designed for the RC2014. Board design files are at <https://github.com/ancientcomputing/rc2014/tree/master/eagle/6502_board_revb>
MCRobbie Breakout v. 1.0.1
author: inmysocks
2 layer board of 1.01 x 1.41 inches (25.6 x 35.7 mm)
Uploaded:
June 18, 2017
Shared:
June 18, 2017
Total Price:
$7.05
VasttraPi Power Control board, rev.2
author: platisd
2 layer board of 2.06 x 1.15 inches (52.4 x 29.2 mm)
Uploaded:
May 18, 2017
Shared:
June 17, 2017
Total Price:
$11.85
A power control board for a Raspberry Pi used in the VasttraPi project. The board has four USB ports. The first one is used to receive power and power up an ATtiny85 microcontroller. The MCU drives a relay to turn on and off the power to two USB ports and t…
Show full description
A power control board for a Raspberry Pi used in the VasttraPi project. The board has four USB ports. The first one is used to receive power and power up an ATtiny85 microcontroller. The MCU drives a relay to turn on and off the power to two USB ports and t…
Show full description
Coinkit-Photon
author: mr_darker
2 layer board of 1.38 x 1.52 inches (35.1 x 38.6 mm)
Uploaded:
March 23, 2017
Shared:
June 17, 2017
Total Price:
$10.50
Coinkit with simple regulator & using Photon Development Board.
Coinkit with simple regulator & using Photon Development Board.
CoinKit SMD Version (Test)
author: mr_darker
2 layer board of 1.04 x 1.75 inches (26.4 x 44.4 mm)
Uploaded:
November 21, 2016
Shared:
June 17, 2017
Total Price:
$9.05
Comms w/ vending machine over the internet. Designed by a complete noob so… hope it works!
Comms w/ vending machine over the internet. Designed by a complete noob so… hope it works!
BLF switch board DDm-K2-SW [rev01][tried and tested]
author: DEL
2 layer board of 0.61 x 0.57 inches (15.4 x 14.4 mm)
Uploaded:
June 02, 2017
Shared:
June 17, 2017
Total Price:
$1.70
Daughter board for the DDm-K2 driver board.
<https://oshpark.com/shared_projects/F9jb3vFP>
The switch is a NO SMD 6.2x6.2x3.1 mm tactile type. The LEDs have 0805 footprints. Normally R1 is not populated. A jumper or small-value resistor here wires the two LEDs to be driven in parallel.
Daughter board for the DDm-K2 driver board.
<https://oshpark.com/shared_projects/F9jb3vFP>
The switch is a NO SMD 6.2x6.2x3.1 mm tactile type. The LEDs have 0805 footprints. Normally R1 is not populated. A jumper or small-value resistor here wires the two LEDs to be driven in parallel.
BLF driver 2.1m-K2 [rev00][tried and tested]
author: DEL
2 layer board of 1.34 x 1.34 inches (34.0 x 34.0 mm)
Uploaded:
June 02, 2017
Shared:
June 17, 2017
Total Price:
$8.95
5+1 7135 driver for Solarstorm/Fandyfire K2 lights.
Revision changes
- New
Needs the DDm-K2-SW daughter board for the tactile switch and indicator LEDs:
<https://oshpark.com/shared_projects/0o6V4Iia>
'Standard' BLF parts list, except for:
- R1 and R2 are populated if MCU pin 7…
Show full description
5+1 7135 driver for Solarstorm/Fandyfire K2 lights.
Revision changes
- New
Needs the DDm-K2-SW daughter board for the tactile switch and indicator LEDs:
<https://oshpark.com/shared_projects/0o6V4Iia>
'Standard' BLF parts list, except for:
- R1 and R2 are populated if MCU pin 7…
Show full description
Flux Capacitor REV2
author: davedarko
2 layer board of 1.00 x 1.20 inches (25.4 x 30.5 mm)
Uploaded:
June 17, 2017
Shared:
June 17, 2017
Total Price:
$6.00
or "Fluxkompensator" as we Germans call it… this is Version 3, with a battery holder and a switch (finally!) Battery holder is for 12mm batteries, holder is the cheapest on ebay. should work with attinyX5 and attiny13. 0805 resistors.
https://hackaday.io/project/25898-flux-capacitor-trinket
or "Fluxkompensator" as we Germans call it… this is Version 3, with a battery holder and a switch (finally!) Battery holder is for 12mm batteries, holder is the cheapest on ebay. should work with attinyX5 and attiny13. 0805 resistors.
https://hackaday.io/project/25898-flux-capacitor-trinket
