Shared Projects

Monitor for wheely bin

Project description

This board is compatible with the Raspberry Pi 3 (B and B+), and is intended to be used with a Roland TD4-KP drum kit in order to provide a fully functional drum module. It is important to note that, the input number 7 is connected to the wrong sensor of the crash cymbal, and should be replaced by input number 6. Another important thing is that there is no hi-hat controller (pedal) input connected.

Components list

• TLC2264
• MCP3008
• LMC7660
• 100k resistors
• 1M potentiometers
• 10µF capacitors
• 220nF capacitor

Resources

Associated Github repositories: eXaDrums-pcb, eXaDrums, libeXaDrums.

Project page on Hackaday: eXaDrums.

Note that this one is for Pulplogic 1U system! Not Intellijel!

Just a little PCB for bringing out RCA connectors to a 1u tile.

Designed so that you can use two of these and stack them with the 4pin header, then you can have RCA connectors inside the case too without hacking up a cable (eg. for Intellijel Springray, or for Music Thing Modular Spring Reverb mk1 without the connectors on the front panel)

for TI INA260 current monitor

for TI INA226 voltage/current sensor with external shunt resistor

v5 has isolation resistors on left side only

Musical Doorbell

DEF CON 506 Group anniversary badge.

IDL_018_034 4 Channel Amplifier THS3202 Version CFA.
Wideband (2GHz) with up to gain of 100 (40dB)

Application for Accelerators Physics Group Input Voltage : +/-3.3~7.5V Max Input Power : 1/25W Input Coupling : DC

Part List. 4x THS3202 bunch of 0603 resistor ranging from 50 ~ 620 2x Dragonfly Connector 8x Vertical SMA

Not Tested Yet, Would not recommend Update 1: Tested, seems to be bad layout thus, oscillation (400MHz-ish Its a great clock,) . Also, forgot the one of the internal layer… it’s 128 so be-careful Update 2: Just replace a output resistor to stop the oscillation. works like a charm.

AMIGA bootselector-addon: puffer of mousebutton on second CIA

https://github.com/MiSTer-devel/Main_MiSTer/wiki/RTC-Board-Assembly-(DIY)

Sparkfun has these great boards with the Qwiic connectors for I2C.

Adafruit has the awesome system of feather boards - which i use a lot.

BOM (Parts List)

Qwiic Connector Part

Stacking Headers for Feather

Editorializing

An abomination against man and god.

Both of these product lines help me create modular tools for work and life. So getting them together would be an even more awesome no-brainer. These are the Lego Blocks of my nihilistic objective correlative.

Breakout board for STMicro LIS3DSH accelerometer

It works with 12AX7, 12AU7, etc.

Board to split out the signals on the DB-25 connector. Power is a standard power connector. The ENA ports are standard 3.5mm connectors. ENA 1 defaults to enabled if nothing is plugged in, ENA 2 and 3 default to disabled when nothing is connected. This is a companion to the DB9 conversion boards here: https://oshpark.com/shared_projects/xm12x143

These are small adapter boards to adapt the pinout of the RLS-1000B to the pinout of the RLC-Club. The RLS-1000B only directly supports logic high PL mode. This includes a small logic inverter to accept logic low signals, and also allows for the COR and PL signals to be tied together for receivers where they are already tied together. For a combined logic low COR and PL system, jumper pins 2-4 and 5-6. The 4 pin header is a provision for the connection of an external PL decoder board, signals as labeled. The companion breakout for the DB25 is here: https://oshpark.com/shared_projects/YJuL8J8m