DG1022-series Output Filters
author: ktemkin
2 layer board of 1.36 x 1.26 inches (34.6 x 32.1 mm)
Uploaded:
July 30, 2014
Shared:
August 18, 2014
Total Price:
$8.60
A pair of output filters which should help to clean up the otherwise-noisy DG1022 series.
A pair of output filters which should help to clean up the otherwise-noisy DG1022 series.
Medusa SRK
author: Mattaus
2 layer board of 1.86 x 1.86 inches (47.3 x 47.3 mm)
Uploaded:
August 04, 2014
Shared:
August 17, 2014
Total Price:
$17.30
Quad XP Footprint array using Carclo 1062X Optics, direct drive via 70N02 FET.
Single XP footprint LED, direct drive via IRLML2502 FET.
RGB XQ array using unknown reflector, each LED driven via 2 AMC7135 linear CC regulators.
Controlled via PIC16F1825 TSSOP.
Intended for MLED Firmware.
Quad XP Footprint array using Carclo 1062X Optics, direct drive via 70N02 FET.
Single XP footprint LED, direct drive via IRLML2502 FET.
RGB XQ array using unknown reflector, each LED driven via 2 AMC7135 linear CC regulators.
Controlled via PIC16F1825 TSSOP.
Intended for MLED Firmware.
CC110L Breakout Board
author: idlehandsdev
2 layer board of 0.83 x 1.22 inches (21.0 x 31.0 mm)
Uploaded:
August 17, 2014
Shared:
August 17, 2014
Total Price:
$5.00
Breakout for CC110X TI RF module - 915mhz
Breakout for CC110X TI RF module - 915mhz
Bike Lightning 2 spoke-V1
author: wittenbunk
2 layer board of 3.00 x 3.00 inches (76.3 x 76.3 mm)
Uploaded:
January 25, 2014
Shared:
August 17, 2014
Total Price:
$45.10
Bike lights 2 spokes
Bike lights 2 spokes
Bike Lightning Light strip V1
author: wittenbunk
2 layer board of 1.30 x 2.30 inches (33.1 x 58.5 mm)
Uploaded:
January 27, 2014
Shared:
August 17, 2014
Total Price:
$15.00
Bike Lightning Light strip V1
Bike Lightning Light strip V1
TeensyGLCD V-1.4
author: jimmayhugh
2 layer board of 2.40 x 2.25 inches (61.0 x 57.2 mm)
Uploaded:
August 17, 2014
Shared:
August 17, 2014
Total Price:
$26.95
7" GLCD as an I2C or 1-wire device
7" GLCD as an I2C or 1-wire device
S.Bus Inverter R2
author: TimJC
2 layer board of 0.36 x 0.91 inches (9.1 x 23.1 mm)
Uploaded:
August 12, 2014
Shared:
August 17, 2014
Total Price:
$1.60
Futaba SBUS to serial inverter. This is used for connecting SBUS compatible RC RXs with Naze32/Flip32 multirotor flight controllers on input pin 4, and enabling "feature SERIALRX" in the Baseflight …
Show full description
Futaba SBUS to serial inverter. This is used for connecting SBUS compatible RC RXs with Naze32/Flip32 multirotor flight controllers on input pin 4, and enabling "feature SERIALRX" in the Baseflight …
Show full description
S3860M-S Breakout v1.0
author: nickswalker
2 layer board of 1.12 x 0.93 inches (28.4 x 23.5 mm)
Uploaded:
August 16, 2014
Shared:
August 17, 2014
Total Price:
$5.15
Stra
Stra
BMI055 Breakout
author: sgstair
2 layer board of 0.70 x 0.80 inches (17.8 x 20.3 mm)
Uploaded:
August 16, 2014
Shared:
August 16, 2014
Total Price:
$2.75
Simple breakout of partial BMI055 functionality that I made to integrate this part into another project
C1: 1uF
C2: 0.01uF
R1: 10k (interrupt line pullup)
The capacitor values aren't critical, but this chip should have some bypass cap installed for local power stability.
Simple breakout of partial BMI055 functionality that I made to integrate this part into another project
C1: 1uF
C2: 0.01uF
R1: 10k (interrupt line pullup)
The capacitor values aren't critical, but this chip should have some bypass cap installed for local power stability.
LED breakout board
author: farsinotare
2 layer board of 1.97 x 1.97 inches (50.0 x 50.0 mm)
Uploaded:
August 15, 2014
Shared:
August 15, 2014
Total Price:
$19.35
Breakout board for 8 LEDs: Control LEDs with a 74hc595 or in parallel with a low side switch
Find the schematic here
Breakout board for 8 LEDs: Control LEDs with a 74hc595 or in parallel with a low side switch
Find the schematic here
LED board
author: pmacdougal
2 layer board of 2.59 x 2.30 inches (65.7 x 58.4 mm)
Uploaded:
March 23, 2013
Shared:
August 15, 2014
Total Price:
$29.75
Four 7-seg LED display board
Four 7-seg LED display board
