OSHPARK
  • About Us
  • Services
  • Support
  • Sharing
  • Log in
  • Sign up
  • OSHPARK
  • About Us
  • Services
  • Support
  • Sharing
  • Log in

HydraESP32 HydraBus v1.0 Shield for ESP-WROOM-32 V1.0 Rev1.1 (Tested)

author: hydrabus
Top
Bottom

2 layer board of 2.37 x 1.47 inches (60.2 x 37.2 mm)
Uploaded: August 15th 2016
Shared: August 15th 2016
Total Price: $17.35

HydraBus_1_0_Shield_ESP_WROOM_32_V1_0_Rev1_1

HydraBus Shield / Breakout board for ESP-WROOM-32.

This shield can be used with or without HydraBus board, you can even cut HydraBus specific right side (on the line) to have a tiny ESP-WROOM-32 breakout board.

  • This shield can be used on top or bottom of HydraBus board (you just need to solder ESP-WROOM-32 on top or bottom of the shield)

  • The HydraBus board is a small (60mm x 37mm) and low cost, multi-tool extensible board with STM32F405 Cortex M4F 32bits MCU @168MHz with a fully open source firmware hydrafw and full online documentation hydrafw wiki

  • The ESP-WROOM-32 is a low-power 32-bit 240 MHz dual core MCU Wi- Fi+BLE combo module that highly integrates TCP/IP network stacks, 12- bit ADC and HSPI/SDIO/UART/PWM/I2C/I2S interfaces. See ESP32 Overview, ESP-WROOM-32 link/info, Espressif Products Overview including ESP-WROOM-32 PDF

  • Design based on official esp_wroom_32_datasheet_en.pdf (August 8, 2016)

The board has been tested (mainly UART with bridge mode of HydraBus/HydraFW) with an ESP-WROOM-32 soldered on bottom side and all work fine

There is only a typo on silkscreen on bottom side at left of IO15 which is labelled GND instead of IO13

See new version HydraESP32 HydraBus v1.0 Shield for ESP-WROOM-32 V1.1 Rev1.0 which fix that and improve a lot this breakout board

HydraBus_1_0_Shield_ESP_WROOM_32_V1_0_Rev1_1

HydraBus Shield / Breakout board for ESP-WROOM-32.

This shield can be used with or without HydraBus board, you can even cut HydraBus specific right side (on the line) to have a tiny ESP-WROOM-32 breakout board.

  • This shield can be used on top or bottom of HydraBus board (you just need to solder ESP-WROOM-32 on top or bottom of the shield)

  • The HydraBus board is a small (60mm x 37mm) and low cost, multi-tool extensible board with STM32F405 Cortex M4F 32bits MCU @168MHz with a fully open source firmware hydrafw and full online documentation hydrafw wiki

  • The ESP-WROOM-32 is a low-power 32-bit 240 MHz dual core MCU Wi- Fi+BLE combo module that highly integrates TCP/IP network stacks, 12- bit ADC and HSPI/SDIO/UART/PWM/I2C/I2S interfaces. See ESP32 Overview, ESP-WROOM-32 link/info, Espressif Products Overview including ESP-WROOM-32 PDF

  • Design based on official esp_wroom_32_datasheet_en.pdf (August 8, 2016)

The board has been tested (mainly UART with bridge mode of HydraBus/HydraFW) with an ESP-WROOM-32 soldered on bottom side and all work fine

There is only a typo on silkscreen on bottom side at left of IO15 which is labelled GND instead of IO13

See new version HydraESP32 HydraBus v1.0 Shield for ESP-WROOM-32 V1.1 Rev1.0 which fix that and improve a lot this breakout board

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
      Order Board Download Permalink Embed link
Embeddable link to order this shared Project
  • COMPANY
  • About Us
  • Blog
  • Shop
  • SERVICES
  • Upload Your File
  • Prototypes
  • HELP
  • Support
  • If you can't find what you're looking for, please contact us at [email protected]
  • CONNECT
  • Shared Projects
  • Log in / Sign up
Whaleshark white
Follow us
© Copyright 2022 Oshpark LLC | Privacy