Power-OR-Circuit-4-Layer
4 layer board of 0.55 x 0.64 inches (14.0 x 16.2 mm)
Uploaded:
December 11th 2022
Shared:
December 12th 2022
Total Price:
$3.40
Power OR circuit using Schottky Diodes made in Altium Circuit Maker with 4 Layers. Testing both OSHPark 4 layer boards and Learning Circuit Maker.
This is a board I made after reading an article on RobotRoom.com by David Cook regarding Solar Charging. link - https://robotroom.com/Solar-Rechargi…
Show full description
Power OR circuit using Schottky Diodes made in Altium Circuit Maker with 4 Layers. Testing both OSHPark 4 layer boards and Learning Circuit Maker.
This is a board I made after reading an article on RobotRoom.com by David Cook regarding Solar Charging. link - https://robotroom.com/Solar-Rechargi…
Show full description
Power-OR-Circuit
2 layer board of 0.50 x 0.90 inches (12.7 x 22.9 mm)
Uploaded:
December 11th 2022
Shared:
December 11th 2022
Total Price:
$2.25
2 Layer functional test board using Altium CircuitMaker with a "Power OR" circuit that has charging capabilities through D3 from P1 which will only charge P2 if D3 is populated. All Voltage signals are pulled out through P3 which can be made breadboard friendly by using a right angle pin header….
Show full description
2 Layer functional test board using Altium CircuitMaker with a "Power OR" circuit that has charging capabilities through D3 from P1 which will only charge P2 if D3 is populated. All Voltage signals are pulled out through P3 which can be made breadboard friendly by using a right angle pin header….
Show full description
MiniStepper V3.1
2 layer board of 0.55 x 0.68 inches (14.0 x 17.3 mm)
Uploaded:
November 4th 2021
Shared:
November 4th 2021
Total Price:
$1.85
A breakout board for a mini linear stepper motor with a 4 pad connector on 0.8mm centers. The board has holes for mounting the frame using solder.
All sizing is guessed, this is my 4th version, V3.1, after size testing the previous 3. The motors are available on [Amazon in qty's of 50](https…
Show full description
A breakout board for a mini linear stepper motor with a 4 pad connector on 0.8mm centers. The board has holes for mounting the frame using solder.
All sizing is guessed, this is my 4th version, V3.1, after size testing the previous 3. The motors are available on [Amazon in qty's of 50](https…
Show full description
1-Button-Keypad
2 layer board of 0.35 x 0.45 inches (9.0 x 11.5 mm)
Uploaded:
October 15th 2020
Shared:
October 15th 2020
Total Price:
$0.75
Single button keypad. Works as Active High or Low by reversing the power input pins as stated on back of board. No mounting holes. Glue/Epoxy in place.
Takes a through hole 6mm push-button tactile switch and a 603 resistor. Will update with real photos when parts are received and tested :)
Single button keypad. Works as Active High or Low by reversing the power input pins as stated on back of board. No mounting holes. Glue/Epoxy in place.
Takes a through hole 6mm push-button tactile switch and a 603 resistor. Will update with real photos when parts are received and tested :)
UFO - V1
2 layer board of 0.66 x 0.68 inches (16.9 x 17.3 mm)
Uploaded:
June 3rd 2019
Shared:
June 3rd 2019
Total Price:
$2.25
A Spinny Thingy. This has some custom pads that I will be testing. V1.0 is a sizing test.
A Spinny Thingy. This has some custom pads that I will be testing. V1.0 is a sizing test.