Basic USB Breakout v1.1
2 layer board of 1.78 x 0.71 inches (45.3 x 17.9 mm)
Uploaded:
January 1st 2017
Shared:
March 18th 2017
Total Price:
$6.25
Breadboard-compatible USB breakout board. Not suitable for USB3.
The micro-USB connector has surface mount pads which may be easier to solder with paste or tinned pads and a hot plate, toaster oven, or hot air rework station.
The [Basic Breakouts Github repo](https://github.com/wickerbox/B…
Show full description
Breadboard-compatible USB breakout board. Not suitable for USB3.
The micro-USB connector has surface mount pads which may be easier to solder with paste or tinned pads and a hot plate, toaster oven, or hot air rework station.
The [Basic Breakouts Github repo](https://github.com/wickerbox/B…
Show full description
MicroSD Connector 5009010801 Breakout v1.1
2 layer board of 1.26 x 0.71 inches (31.9 x 17.9 mm)
Uploaded:
March 18th 2017
Shared:
March 18th 2017
Total Price:
$4.40
Breadboard-compatible breakout for a micro SD card.
The board has surface mount parts which may be easier to solder with paste or tinned pads and a hot plate, toaster oven, or hot air rework station.
The [Basic Breakouts Github repo](https://github.com/wickerbox/Basic-Breakout-Boards/tree…
Show full description
Breadboard-compatible breakout for a micro SD card.
The board has surface mount parts which may be easier to solder with paste or tinned pads and a hot plate, toaster oven, or hot air rework station.
The [Basic Breakouts Github repo](https://github.com/wickerbox/Basic-Breakout-Boards/tree…
Show full description
Atmega328 Breakout Board v1.2
2 layer board of 1.41 x 1.91 inches (35.7 x 48.4 mm)
Uploaded:
March 10th 2017
Shared:
March 18th 2017
Total Price:
$13.35
Basic breakout board for the Atmega328 to prove out a KiCad template.
Just add a bootloader using another Arduino and Nick Gammon's Bootloader, then use an FTDI cable to program this board directly.
The [Github repo](https://github.com/wickerbox/…
Show full description
Basic breakout board for the Atmega328 to prove out a KiCad template.
Just add a bootloader using another Arduino and Nick Gammon's Bootloader, then use an FTDI cable to program this board directly.
The [Github repo](https://github.com/wickerbox/…
Show full description
FGPMMOPA6H GPS Breakout v1.1
2 layer board of 1.71 x 1.11 inches (43.4 x 28.1 mm)
Uploaded:
February 24th 2017
Shared:
March 14th 2017
Total Price:
$9.45
Basic breakout board for the FGPMMOPA6H GPS module.
To use with a 5V FTDI cable and your computer, orient cable with RESET (green) at pin 1 on J1.
To use with 5V controllers, connect VCC, 5V_RX, 5V_TX, and GND.
To use with 3.3V controllers, connect VCC, 5V_RX, 3.3V_TX, and GND.
The [G…
Show full description
Basic breakout board for the FGPMMOPA6H GPS module.
To use with a 5V FTDI cable and your computer, orient cable with RESET (green) at pin 1 on J1.
To use with 5V controllers, connect VCC, 5V_RX, 5V_TX, and GND.
To use with 3.3V controllers, connect VCC, 5V_RX, 3.3V_TX, and GND.
The [G…
Show full description
E202VAR VLF Radio Receiver v1.4
2 layer board of 2.21 x 3.21 inches (56.1 x 81.5 mm)
Uploaded:
March 14th 2017
Shared:
March 14th 2017
Total Price:
$35.35
An open source version of Renato Romero’s portable E202 VLF radio receiver, made with permission.
This board was built and verified by listening through headphones. It needs a full test of functionality, but I leave that to someone in the VLF c…
Show full description
An open source version of Renato Romero’s portable E202 VLF radio receiver, made with permission.
This board was built and verified by listening through headphones. It needs a full test of functionality, but I leave that to someone in the VLF c…
Show full description
