OSHPARK
  • About Us
  • Services
  • Support
  • Sharing
  • Log in
  • Sign up
  • OSHPARK
  • About Us
  • Services
  • Support
  • Sharing
  • Log in

ArduinoISP header shield v0.2(tested)

author: Omagasohe
Top
Bottom

2 layer board of 2.03 x 0.49 inches (51.5 x 12.3 mm)
Uploaded: August 26, 2015
Shared: September 20, 2015
Total Price: $4.90

Fixed the 2x3 header and added blinky lights.

Blog post 1 Blog post 2 I was looking for an “Arduino as ISP” shield to program a few dev boards, but the shields are all for IC sockets. I wanted simple, and cheap.

This will need a 2x3 IDC ribbon cable and a way to get it on the other side, adafruit has the cable and the breakout for all of $3 if you want to go that route, don’t forget a few male headers if you need them.

There is a footprint for a 10uF cap if it’s needed, i didn’t but it’s there if you do. The led’s are optional, but who doesn’t like blinking stuff. They fit on the board and didn’t cost extra. I designed them to work with wires dropping down hence the silk on the bottom. you can’t really see it but the board is notched on the right for access to pin 9. IT’s enough for a breadboard wire to work well, the hole for the wire on the bottom is tight for 22(7) I snipped a strand off to make it fit better.

Hint: this isn’t straight across. You’ll need to solder the headers with it on the arduino. the header holes allow for enough play. Once soldered it’s perfect and slides right in and out.

Dip trace file for the board is in the zip.

Alt text

Fixed the 2x3 header and added blinky lights.

Blog post 1 Blog post 2 I was looking for an “Arduino as ISP” shield to program a few dev boards, but the shields are all for IC sockets. I wanted simple, and cheap.

This will need a 2x3 IDC ribbon cable and a way to get it on the other side, adafruit has the cable and the breakout for all of $3 if you want to go that route, don’t forget a few male headers if you need them.

There is a footprint for a 10uF cap if it’s needed, i didn’t but it’s there if you do. The led’s are optional, but who doesn’t like blinking stuff. They fit on the board and didn’t cost extra. I designed them to work with wires dropping down hence the silk on the bottom. you can’t really see it but the board is notched on the right for access to pin 9. IT’s enough for a breadboard wire to work well, the hole for the wire on the bottom is tight for 22(7) I snipped a strand off to make it fit better.

Hint: this isn’t straight across. You’ll need to solder the headers with it on the arduino. the header holes allow for enough play. Once soldered it’s perfect and slides right in and out.

Dip trace file for the board is in the zip.

Alt text

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project
  • COMPANY
  • About Us
  • Blog
  • Shop
  • SERVICES
  • Upload Your File
  • Prototypes
  • HELP
  • Support
  • If you can't find what you're looking for, please contact us at [email protected]
  • CONNECT
  • Shared Projects
  • Log in / Sign up
Whaleshark white
Follow us
© Copyright 2025 OSH Park, LLC | Privacy