Brew Bubbles Shield v1.0
author: LBussy
2 layer board of 1.01 x 1.13 inches (25.6 x 28.7 mm)
Uploaded:
October 06, 2019
Shared:
October 06, 2019
Total Price:
$5.65
This shield provides the necessary component connections and circuitry for the Brew Bubbles project. It is nearly identical in size to the Wemos D1 mini we use to provide a very compact and lightweight footprint.
Bill of Materials
General Parts
Since this uses 1 or 2 each of very common, very inexpensive components, you may find you are better off buying a resistor assortment for instance or end up buying 10 or 20 at a time. Make several!
| Quan | Description | Placement |
|---|---|---|
| 3 | 0.1μF 10V Ceramic Capacitor | C1, C2. C3 |
| *2 | 2.2kΩ 1/4W 5% Axial resistor | R1, R2 |
| 1 | 150Ω 1/4W 5% Axial resistor | R3 |
| *2 | 3-Pin 90° Header | VESSEL, ROOM |
| 1 | Sharp GP1A57HR Transmissive Photointerrupter | U1 |
This BOM is available on Mouser via this link.
Other Parts
| Quan | Description | Placement |
|---|---|---|
| 1 | Wemos D1 Mini R2 | U2 |
| 2 | 8-pin male stackable header (nearly always comes with the D1) | |
| 2 | 8-pin female stackable header (nearly always comes with the D1) | |
| *2 | Waterproof DS18B20 Temperature Sensor with lead | VESSEL, ROOM |
Optional Parts
The items marked with an *asterisk above are optional. They are in the design to provide a means to monitor and trend one’s ambient temperature where the fermenter is placed, and/or the fermenting liquid’s temperature via a thermowell or insulated in contact with the fermenter. If one chooses not to use these, the firmware will automatically skip reporting these readings.
This shield provides the necessary component connections and circuitry for the Brew Bubbles project. It is nearly identical in size to the Wemos D1 mini we use to provide a very compact and lightweight footprint.
Bill of Materials
General Parts
Since this uses 1 or 2 each of very common, very inexpensive components, you may find you are better off buying a resistor assortment for instance or end up buying 10 or 20 at a time. Make several!
| Quan | Description | Placement |
|---|---|---|
| 3 | 0.1μF 10V Ceramic Capacitor | C1, C2. C3 |
| *2 | 2.2kΩ 1/4W 5% Axial resistor | R1, R2 |
| 1 | 150Ω 1/4W 5% Axial resistor | R3 |
| *2 | 3-Pin 90° Header | VESSEL, ROOM |
| 1 | Sharp GP1A57HR Transmissive Photointerrupter | U1 |
This BOM is available on Mouser via this link.
Other Parts
| Quan | Description | Placement |
|---|---|---|
| 1 | Wemos D1 Mini R2 | U2 |
| 2 | 8-pin male stackable header (nearly always comes with the D1) | |
| 2 | 8-pin female stackable header (nearly always comes with the D1) | |
| *2 | Waterproof DS18B20 Temperature Sensor with lead | VESSEL, ROOM |
Optional Parts
The items marked with an *asterisk above are optional. They are in the design to provide a means to monitor and trend one’s ambient temperature where the fermenter is placed, and/or the fermenting liquid’s temperature via a thermowell or insulated in contact with the fermenter. If one chooses not to use these, the firmware will automatically skip reporting these readings.
