Shared projects

5110mega328

2 layer board of 1.59 x 1.40 inches (40.3 x 35.6 mm).
Shared on May 21st, 2018 06:21


5110mega328

2 layer board of 1.59 x 1.40 inches (40.3 x 35.6 mm).
Shared on May 21st, 2018 06:21



st7735Splate

2 layer board of 0.39 x 0.79 inches (9.9 x 19.9 mm).
Shared on April 11th, 2018 19:33

UNTESTED just a basic interface plate for this cheapo screen https://www.aliexpress.com/item/QH86-1-44-Inch-1-44-Serial-SPI-Resolution-128X128-Driver-IC-ST7735S-True-Color-TFT/32803895039.html

you will need an 0805 resistor, normally about 10ohm

just watch the pin numbers on the screen!!!


st7735Splate

2 layer board of 0.39 x 0.79 inches (9.9 x 19.9 mm).
Shared on April 11th, 2018 19:33

UNTESTED just a basic interface plate for this cheapo screen https://www.aliexpress.com/item/QH86-1-44-Inch-1-44-Serial-SPI-Resolution-128X128-Driver-IC-ST7735S-True-Color-TFT/32803895039.html

you will need an 0805 resistor, normally about 10ohm

just watch the pin numbers on the screen!!!



hohoho.brd

2 layer board of 3.08 x 3.38 inches (78.1 x 85.9 mm).
Shared on January 4th, 2018 10:26


hohoho.brd

2 layer board of 3.08 x 3.38 inches (78.1 x 85.9 mm).
Shared on January 4th, 2018 10:26



keyTop.brd

2 layer board of 1.50 x 3.00 inches (38.2 x 76.2 mm).
Shared on November 7th, 2017 13:35

A custom keayboard top plate maker. All holes are 2.5mm and plated, so any holes can either be bolted or soldered together!! Use 0.8mm pcb to allow boards overlapping for strength, and you will end up with 1.6mm thickness :) UNTESTED!!


keyTop.brd

2 layer board of 1.50 x 3.00 inches (38.2 x 76.2 mm).
Shared on November 7th, 2017 13:35

A custom keayboard top plate maker. All holes are 2.5mm and plated, so any holes can either be bolted or soldered together!! Use 0.8mm pcb to allow boards overlapping for strength, and you will end up with 1.6mm thickness :) UNTESTED!!



iliPlate.brd

2 layer board of 0.46 x 0.89 inches (11.6 x 22.7 mm).
Shared on September 13th, 2017 19:35

minimal interface board for ili9341 screens. R1 is a 10ohm resistor (0805 size) , but can be replaced with other values to adjust backlight brightness. The less commonly used touch interface pins are broke out to pads on the back. can be used for 2.2" screens also, just make sure you line from pin 1. contact moosepr@gmail.com


iliPlate.brd

2 layer board of 0.46 x 0.89 inches (11.6 x 22.7 mm).
Shared on September 13th, 2017 19:35

minimal interface board for ili9341 screens. R1 is a 10ohm resistor (0805 size) , but can be replaced with other values to adjust backlight brightness. The less commonly used touch interface pins are broke out to pads on the back. can be used for 2.2" screens also, just make sure you line from pin 1. contact moosepr@gmail.com