Hey there! Before ordering, make sure you have all all the info you need to complete and use this design.
This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended.
OSH Park cannot place any guarantees about the functionality or correctness of the design.
Hey there! Before ordering, make sure you have all all the info you need to complete and use this design.
This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended.
OSH Park cannot place any guarantees about the functionality or correctness of the design.
Hey there! Before ordering, make sure you have all all the info you need to complete and use this design.
This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended.
OSH Park cannot place any guarantees about the functionality or correctness of the design.
2 layer board of 4.06 x 0.89 inches (103.2 x 22.6 mm)
Uploaded:
May 23rd 2014
Shared:
January 8th 2015
Total Price:
$18.00
Based on gaussmarkov's project at http://gaussmarkov.net/wordpress/circuits/dr-boogey/
There are a few extra parts on the board. The extra capacitor C22 a…
Based on gaussmarkov’s project at http://gaussmarkov.net/wordpress/circuits/dr-boogey/
There are a few extra parts on the board. The extra capacitor C22 and the switch SW1 are for a raw/vintage/modern mod. I used a 470nF cap for C22 and a SPDT center off switch for SW1 but you can leave off C22 and solder all three pads for SW1 together if you want a standard Dr Boogie. The only other ‘extra’ is R21 which goes from lug 1 to lug 3 of the MID pot. That way you can use a 5k audio pot and a 5k resistor for R21 to make a psuedo-linear 2.5k pot. Leave it off if your using a 2k or 2.5k pot.
Based on gaussmarkov's project at http://gaussmarkov.net/wordpress/circuits/dr-boogey/
There are a few extra parts on the board. The extra capacitor C22 a…
Based on gaussmarkov’s project at http://gaussmarkov.net/wordpress/circuits/dr-boogey/
There are a few extra parts on the board. The extra capacitor C22 and the switch SW1 are for a raw/vintage/modern mod. I used a 470nF cap for C22 and a SPDT center off switch for SW1 but you can leave off C22 and solder all three pads for SW1 together if you want a standard Dr Boogie. The only other ‘extra’ is R21 which goes from lug 1 to lug 3 of the MID pot. That way you can use a 5k audio pot and a 5k resistor for R21 to make a psuedo-linear 2.5k pot. Leave it off if your using a 2k or 2.5k pot.
Hey there! Before ordering, make sure you have all all the info you need to complete and use this design.
This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended.
OSH Park cannot place any guarantees about the functionality or correctness of the design.
Hey there! Before ordering, make sure you have all all the info you need to complete and use this design.
This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended.
OSH Park cannot place any guarantees about the functionality or correctness of the design.
