OSH Park ~ Shared Projects by The_Real

JTAG Prog Helper

2 layer board of 1.30 x 1.20 inches (33.0 x 30.5 mm)
Uploaded: January 27, 2023
Shared: August 12, 2023
Total Price: $7.80

Used for my Virtual Tap's CPLD programming. Use a mini USB for power, and JTAG standard connection from USB Blaster.

Top

Bottom

Embeddable link to order this shared Project

RED RIBBON for Virtual Boy

Top

Bottom

2 layer board of 0.98 x 2.74 inches (24.8 x 69.6 mm)
Uploaded: July 21, 2023
Shared: July 21, 2023
Total Price: $13.35

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You'll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best …

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You’ll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best is a micro scissor)

4. Install the ribbon with flux, and use a multimeter to avoid bridges

5. Wrap the base (lens side) with capton tape to insolate the soldering and give a bit of strenght of the installation.

Show full description

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You'll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best …

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You’ll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best is a micro scissor)

4. Install the ribbon with flux, and use a multimeter to avoid bridges

5. Wrap the base (lens side) with capton tape to insolate the soldering and give a bit of strenght of the installation.

Show full description

Top

Bottom

Embeddable link to order this shared Project

RGBS AMP + Audio 1in/2out

Top

Bottom

2 layer board of 2.35 x 1.70 inches (59.7 x 43.2 mm)
Uploaded: July 15, 2023
Shared: July 15, 2023
Total Price: $19.95

Screw terminals can be https://www.digikey.ca/en/products/detail/phoenix-contact/1751264/2511021 but any 3.50 spacing ones should be good I'd like to test https://www.digikey.ca/en/products/detail/adam-tech/EBWA-04-A/9830530 which are cheaper

I put the ref for the trimpots in back https://www.d…

Screw terminals can be https://www.digikey.ca/en/products/detail/phoenix-contact/1751264/2511021 but any 3.50 spacing ones should be good I’d like to test https://www.digikey.ca/en/products/detail/adam-tech/EBWA-04-A/9830530 which are cheaper

I put the ref for the trimpots in back https://www.digikey.ca/en/products/detail/nidec-components-corporation/CT-6EP102/738303

Electrolytic caps are https://www.digikey.ca/en/products/detail/panasonic-electronic-components/ECE-A1CN330U/227606 and https://www.digikey.ca/en/products/detail/panasonic-electronic-components/ECA-1AM331/244984

33uF are bipolar (unpolarized)

Switch can be something like https://www.digikey.ca/en/products/detail/c-k/OS102011MS2QN1/411602

The rest is on the back of the PCBs

And of course the THS7374

Show full description

I put the ref for the trimpots in back https://www.d…

I put the ref for the trimpots in back https://www.digikey.ca/en/products/detail/nidec-components-corporation/CT-6EP102/738303

33uF are bipolar (unpolarized)

Switch can be something like https://www.digikey.ca/en/products/detail/c-k/OS102011MS2QN1/411602

The rest is on the back of the PCBs

And of course the THS7374

Show full description

Top

Bottom

Embeddable link to order this shared Project

DFO + Switchless Genesis

Top

Bottom

2 layer board of 0.60 x 0.84 inches (15.2 x 21.3 mm)
Uploaded: May 24, 2023
Shared: May 24, 2023
Total Price: $2.50

Top

Bottom

Embeddable link to order this shared Project

Genesis RGB Led SMD

Top

Bottom

2 layer board of 0.41 x 0.30 inches (10.5 x 7.6 mm)
Uploaded: February 19, 2017
Shared: May 24, 2023
Total Price: $0.60

Genesis RGB Led SMD

Top

Bottom

Embeddable link to order this shared Project

← Previous
1
2
3
4
Next →

COMPANY
About Us
Blog
Shop

HELP
Support
If you can't find what you're looking for, please contact us at [email protected]

Shared Projects by The_Real_Phoenix

Shared Projects by The_Real_Phoenix

JTAG Prog Helper

RED RIBBON for Virtual Boy

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You'll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best …

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You’ll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best is a micro scissor)

4. Install the ribbon with flux, and use a multimeter to avoid bridges

5. Wrap the base (lens side) with capton tape to insolate the soldering and give a bit of strenght of the installation.

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You'll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best …

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You’ll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best is a micro scissor)

4. Install the ribbon with flux, and use a multimeter to avoid bridges

5. Wrap the base (lens side) with capton tape to insolate the soldering and give a bit of strenght of the installation.

RGBS AMP + Audio 1in/2out

DFO + Switchless Genesis

Genesis RGB Led SMD

Shared Projects by The_Real_Phoenix

Shared Projects by The_Real_Phoenix

JTAG Prog Helper

Ordering shared project

RED RIBBON for Virtual Boy

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You'll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best …

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You’ll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best is a micro scissor)

4. Install the ribbon with flux, and use a multimeter to avoid bridges

5. Wrap the base (lens side) with capton tape to insolate the soldering and give a bit of strenght of the installation.

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You'll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best …

The is a replacement for the Virtual Boy lenses' ribbon cable.

Order them in flex PCB.

You’ll have to:

1. Remove the old ribbon cable from the lens

2. Salvage the cardboard stiffer from it

3. Cut the vias following the line to castellated them (use an Xacto knife, best is a micro scissor)

4. Install the ribbon with flux, and use a multimeter to avoid bridges

5. Wrap the base (lens side) with capton tape to insolate the soldering and give a bit of strenght of the installation.

Ordering shared project

RGBS AMP + Audio 1in/2out

Ordering shared project

DFO + Switchless Genesis

Ordering shared project

Genesis RGB Led SMD

Ordering shared project