WT90 Carrier without charging PCB V1
2 layer board of 1.84 x 1.84 inches (46.8 x 46.8 mm)
Uploaded:
April 11, 2022
Shared:
April 11, 2022
Total Price:
$17.00
This is a replacement PCB for the WT90 that removes the charging and thus any parasitic drain on the cells.
It has not been officially tested but should work, just be careful during the first test and only use one cell .
You do this at your own risk. This modification also removes all polar…
Show full description
This is a replacement PCB for the WT90 that removes the charging and thus any parasitic drain on the cells.
It has not been officially tested but should work, just be careful during the first test and only use one cell .
You do this at your own risk. This modification also removes all polar…
Show full description
47.5mm Q8 Texas Avenger driver with mounting holes
2 layer board of 1.88 x 1.88 inches (47.6 x 47.6 mm)
Uploaded:
July 16, 2017
Shared:
July 16, 2017
Total Price:
$17.55
This is the normal SRK / Q8 driver in 47.5mm size and with the Q8 mounting holes. Only really useful for the Q8. You might need to leave some of the 7135's off in order to clear the mounting tabs on the Q8.
This is the normal SRK / Q8 driver in 47.5mm size and with the Q8 mounting holes. Only really useful for the Q8. You might need to leave some of the 7135's off in order to clear the mounting tabs on the Q8.
17mm TA driver with less vias
2 layer board of 0.68 x 0.68 inches (17.2 x 17.2 mm)
Uploaded:
July 16, 2017
Shared:
July 16, 2017
Total Price:
$2.25
This is the same as the normal 17mm TA driver but with less vias under the FET. This makes a short less likely when soldering on the ground wire for the LED but also increases resistance a bit. Both will work just fine and are exactly the same in every other way.
This is the same as the normal 17mm TA driver but with less vias under the FET. This makes a short less likely when soldering on the ground wire for the LED but also increases resistance a bit. Both will work just fine and are exactly the same in every other way.
Q8 5050 LED MCPCb
2 layer board of 1.50 x 1.50 inches (38.2 x 38.2 mm)
Uploaded:
June 27, 2017
Shared:
June 27, 2017
Total Price:
$11.25
Prototype MCPCB for the Q8 with 5050 "XM-L" LED pads and adjustable layout.
Prototype MCPCB for the Q8 with 5050 "XM-L" LED pads and adjustable layout.
46mm LDO - SRK Texas Avenger
2 layer board of 1.82 x 1.82 inches (46.2 x 46.2 mm)
Uploaded:
June 15, 2017
Shared:
June 15, 2017
Total Price:
$16.50
TA46 LDO - 46mm Skyray driver that has an LDO setup with a single contact*
This driver is basically the same as the TA46 LDO 2s or 4S except it has a single contact pad. This means that you will need to use a cell carrier to get the input voltage setup for 2s or 4s. It can accept and work with…
Show full description
TA46 LDO - 46mm Skyray driver that has an LDO setup with a single contact*
This driver is basically the same as the TA46 LDO 2s or 4S except it has a single contact pad. This means that you will need to use a cell carrier to get the input voltage setup for 2s or 4s. It can accept and work with…
Show full description
