Shared Projects by ikrananka

Composite video mod for Odyssey 2 video game consoles (type 2 of 2). Personally, I found that the type 1 mod gave a better (sharper) image quality compared to the type 2.

Mounts in the location of the existing RF unit which must be removed. Use #10 nylon washers (2 in top hole and 1 in the bottom hole) which allows the existing screws to tighten down and hold the board in place.

Bill of Materials

x3 - 100uF electrolytic capacitor (Digi-Key : P5540-ND)

x1 - 10uF electrolytic capacitor (Digi-Key : P19445CT-ND)

x1 - 2N3904 NPN TO-92 transistor (Digi-Key : 2N3904TAFSCT-ND)

x1 - 10 ohm 0.25W metal film resistor (Digi-Key : S10CACT-ND)

x1 - 75 ohm 0.25W metal film resistor (Digi-Key : S75CACT-ND)

x1 - 1.6K ohm 0.25W metal film resistor (Digi-Key : S1.6KCACT-ND)

x1 - 2K ohm 0.25W metal film resistor (Digi-Key : S2KCACT-ND)

x1 - 4 position 0.1" vertical male Molex connector (Digi-Key : WM4202-ND)

x1 - 3 position 0.1" vertical male Molex connector (Digi-Key : WM4201-ND)

x1 - 4 position 0.1" female Molex connector (Digi-Key : WM2002-ND)

x1 - 3 position 0.1" female Molex connector (Digi-Key : WM2001-ND)

x7 - 22-30awg Molex wire crimp terminal (Digi-Key : WM1114-ND)

x3 - #10 nylon washer (Digi-Key : 36-3212-ND)

22-30awg hook-up wire. I used 24awg wire of the following lengths: * Red (+5V) = 17cm * White (Audio) = Input 16cm : Output 19cm * Yellow (Video) = Input 15cm : Output 20cm * Black (GND) = Input 14cm : Output 22cm

3 RCA connectors of your choice.

Composite video mod for Odyssey 2 video game consoles (type 1 of 2). Personally, I found that the type 1 mod gave a better (sharper) image quality compared to the type 2.

Mounts in the location of the existing RF unit which must be removed. Use #10 nylon washers (2 in top hole and 1 in the bottom hole) which allows the existing screws to tighten down and hold the board in place.

Bill of Materials

x1 - 100nF (0.1uF) ceramic capacitor (Digi-Key : 399-14036-1-ND)

x1 - 1k ohm CT6 potentiometer (Digi-Key : CT6EP102-ND)

x1 - BC548 NPN TO-92 transistor (Digi-Key : BC548BTACT-ND)

x1 - BC558 PNP TO-92 transistor (Digi-Key : BC558BTACT-ND)

x1 - 220 ohm 0.25W metal film resistor (Digi-Key : S220CACT-ND)

x1 - 680 ohm 0.25W metal film resistor (Digi-Key : S680CACT-ND)

x1 - 4 position 0.1" vertical male Molex connector (Digi-Key : WM4202-ND)

x1 - 3 position 0.1" vertical male Molex connector (Digi-Key : WM4201-ND)

x1 - 4 position 0.1" female Molex connector (Digi-Key : WM2002-ND)

x1 - 3 position 0.1" female Molex connector (Digi-Key : WM2001-ND)

x7 - 22-30awg Molex wire crimp terminal (Digi-Key : WM1114-ND)

x3 - #10 nylon washer (Digi-Key : 36-3212-ND)

22-30awg hook-up wire. I used 24awg wire of the following lengths: * Red (+5V) = 17cm * White (Audio) = Input 16cm : Output 19cm * Yellow (Video) = Input 15cm : Output 20cm * Black (GND) = Input 14cm : Output 22cm

3 RCA connectors of your choice.