Powered Up Sniffer.kicad_pcb
2 layer board of 0.68 x 0.80 inches (17.2 x 20.4 mm)
Uploaded:
April 23rd 2020
Shared:
April 24th 2020
Total Price:
$2.70
Board with solder points for LEGO Powered Up female header and male cable, with standard 0.1" pin header point for easy jumper experimentation.
Be sure to order the THIN board, 0.8mm thickness! The female sockets have two mounting posts that “snap in” through the board. The neck is only about …
Show full description
Board with solder points for LEGO Powered Up female header and male cable, with standard 0.1" pin header point for easy jumper experimentation.
Be sure to order the THIN board, 0.8mm thickness! The female sockets have two mounting posts that “snap in” through the board. The neck is only about …
Show full description
Powered Up to Power Functions.kicad_pcb
2 layer board of 0.34 x 0.28 inches (8.7 x 7.2 mm)
Uploaded:
March 26th 2020
Shared:
April 24th 2020
Total Price:
$0.45
Board to interface between a LEGO Powered Up (PU) cable and the old Power Functions (PF) cable. Board is hard-wired to present to the PU controller as a Train Motor. Vcc and Gnd are not connected to the PF connector by default, but can be connected by bridging the adjacent pads.
Board to interface between a LEGO Powered Up (PU) cable and the old Power Functions (PF) cable. Board is hard-wired to present to the PU controller as a Train Motor. Vcc and Gnd are not connected to the PF connector by default, but can be connected by bridging the adjacent pads.
City Hub Battery Insert.kicad_pcb
2 layer board of 1.13 x 0.73 inches (28.6 x 18.5 mm)
Uploaded:
April 23rd 2020
Shared:
April 24th 2020
Total Price:
$4.10
Adapter to allow a standard 9V battery lead to be connected in place of the original 6x AAA battery holder in LEGO part 88009, aka "HUB NO. 4" or "City Hub" or "Train Hub".
Adapter to allow a standard 9V battery lead to be connected in place of the original 6x AAA battery holder in LEGO part 88009, aka "HUB NO. 4" or "City Hub" or "Train Hub".
Powered Up Splitter.kicad_pcb
2 layer board of 1.21 x 0.52 inches (30.8 x 13.1 mm)
Uploaded:
April 23rd 2020
Shared:
April 24th 2020
Total Price:
$3.10
Splitter that takes one LEGO Powered Up cable and splits it into two sockets. The ID pins are only connected to the primary socket. The PWM pins used to drive the secondary socket can be driven the same as the primary ("same") or with reverse polarity ("reversed"), depending which jumper is set…
Show full description
Splitter that takes one LEGO Powered Up cable and splits it into two sockets. The ID pins are only connected to the primary socket. The PWM pins used to drive the secondary socket can be driven the same as the primary ("same") or with reverse polarity ("reversed"), depending which jumper is set…
Show full description
Powered Up Extender.kicad_pcb
2 layer board of 0.58 x 0.43 inches (14.8 x 10.9 mm)
Uploaded:
March 26th 2020
Shared:
April 24th 2020
Total Price:
$1.25
Simple board that accepts a LEGO Powered Up female socket and male cable to make an extension cable.
Be sure to order the THIN board, 0.8mm thickness! The female sockets have two mounting posts that "snap in" through the board. The neck is only about 1mm long, so will probably not snap prope…
Show full description
Simple board that accepts a LEGO Powered Up female socket and male cable to make an extension cable.
Be sure to order the THIN board, 0.8mm thickness! The female sockets have two mounting posts that "snap in" through the board. The neck is only about 1mm long, so will probably not snap prope…
Show full description
