Shared projects

N64 Advanced

4 layer board of 2.54 x 1.49 inches (64.5 x 37.7 mm).
Shared on February 5th, 2018 10:45

Version: N64A_20180205
Former Version: N64A_20171204
Last Change: J6 removed
More information about the project on GitHub

Important Note
If you ordered version N64A_20171017 - like I did -, you can unfortunately throw them away :(. There was a design error in the board such that there is a short in an internal plane between VCCDPLL (1.2V) and VCCA (2.5V), which is not easy to fix (fix would need some trace cuts and rewiring)


N64 Advanced

4 layer board of 2.54 x 1.49 inches (64.5 x 37.7 mm).
Shared on February 5th, 2018 10:45

Version: N64A_20180205
Former Version: N64A_20171204
Last Change: J6 removed
More information about the project on GitHub

Important Note
If you ordered version N64A_20171017 - like I did -, you can unfortunately throw them away :(. There was a design error in the board such that there is a short in an internal plane between VCCDPLL (1.2V) and VCCA (2.5V), which is not easy to fix (fix would need some trace cuts and rewiring)



N64-RGB-DAC Mod (v1)

2 layer board of 1.93 x 1.28 inches (48.9 x 32.4 mm).
Shared on January 21st, 2018 19:17

Version: N64RGBv1_20180121
More information about the project on GitHub


N64-RGB-DAC Mod (v1)

2 layer board of 1.93 x 1.28 inches (48.9 x 32.4 mm).
Shared on January 21st, 2018 19:17

Version: N64RGBv1_20180121
More information about the project on GitHub



MAV-NUS / AVDC-NUS BreakOut Adapter (4x)

2 layer board of 0.80 x 1.10 inches (20.4 x 27.9 mm).
Shared on November 8th, 2017 22:29

More information about the project on GitHub


A small adapter for the N64 RGB mod. With this set you get 12 PCBs per Order. Note that castellated edges are not fully supported. It might be happen that not every PCB is 100% good or some PCBs need rework.
- use the service with 0.8mm substrate thickness.
- preparation: make sure that there are no shorts between adjacent pads on the MAV-NUS-side of the PCB due to the manufacturing process.
- installation: hold the PCB to the MAV-NUS / AVDC-NUS (pin 1 to pin 13), solder and fix the PCB in place if needed.


If you intend to buy the RGB modding board from viletim and you have a MAV-NUS or AVDC-NUS inside your N64, I suggest you to buy the flex cable there, too, as the istallation should be easier with the flex cable, though.


MAV-NUS / AVDC-NUS BreakOut Adapter (4x)

2 layer board of 0.80 x 1.10 inches (20.4 x 27.9 mm).
Shared on November 8th, 2017 22:29

More information about the project on GitHub


A small adapter for the N64 RGB mod. With this set you get 12 PCBs per Order. Note that castellated edges are not fully supported. It might be happen that not every PCB is 100% good or some PCBs need rework.
- use the service with 0.8mm substrate thickness.
- preparation: make sure that there are no shorts between adjacent pads on the MAV-NUS-side of the PCB due to the manufacturing process.
- installation: hold the PCB to the MAV-NUS / AVDC-NUS (pin 1 to pin 13), solder and fix the PCB in place if needed.


If you intend to buy the RGB modding board from viletim and you have a MAV-NUS or AVDC-NUS inside your N64, I suggest you to buy the flex cable there, too, as the istallation should be easier with the flex cable, though.



N64 Advanced - Filter AddOn

2 layer board of 1.06 x 0.85 inches (26.8 x 21.6 mm).
Shared on September 28th, 2017 10:53

More information about the project on GitHub


Order this board with 0.8mm substrate thickness!


N64 Advanced - Filter AddOn

2 layer board of 1.06 x 0.85 inches (26.8 x 21.6 mm).
Shared on September 28th, 2017 10:53

More information about the project on GitHub


Order this board with 0.8mm substrate thickness!



N64 RGB Amp... (V1.2)

2 layer board of 0.71 x 1.13 inches (18.0 x 28.6 mm).
Shared on July 18th, 2017 06:37

…based on a THS7374 / THS7373 for the ‘simple’ RGB out modification (NUS-CPU-01..04).

Order this board with a substrate thickness of 0.8mm!


More information about the project on GitHub


N64 RGB Amp... (V1.2)

2 layer board of 0.71 x 1.13 inches (18.0 x 28.6 mm).
Shared on July 18th, 2017 06:37

…based on a THS7374 / THS7373 for the ‘simple’ RGB out modification (NUS-CPU-01..04).

Order this board with a substrate thickness of 0.8mm!


More information about the project on GitHub