2 layer board of 1.89 x 1.73 inches (48.0 x 44.0 mm)
Uploaded:
June 28, 2020
Shared:
August 05, 2020
Total Price:
$16.35
Allows you to easily attach a Wemos D1 Mini to a 2.8" or 3.2" with a 14 Pin Header. Examples of these displays can be found here (3.2") and here (2.4"). Many other vendors sell them as well.
Th…
Allows you to easily attach a Wemos D1 Mini to a 2.8" or 3.2" with a 14 Pin Header. Examples of these displays can be found here (3.2") and here (2.4"). Many other vendors sell them as well.
The pins on the display header are connected to the pins on the D1 Mini as follows:
| TFT Pin |
Name |
D1 Pin |
| 1 |
T_IRQ |
D1 |
| 2 |
T_DO |
D6 |
| 3 |
T_DIN |
D7 |
| 4 |
T_CS |
D2 |
| 5 |
T_CLK |
D5 |
| 6 |
SDO (MISO) |
D6 |
| 7 |
LED |
D0 |
| 8 |
SCK |
D5 |
| 9 |
SDI (MOSI) |
D7 |
| 10 |
DC |
D4 |
| 11 |
RESET |
3V3 |
| 12 |
CS |
D8 |
| 13 |
GND |
G |
| 14 |
VCC |
3V3 |
Note: The LED pin controls the brightness of the display backlight. It is connected to D0 on the D1 Mini, so your code will need to set that HIGH for full brightness, or PWM it for dimmer values.
The board also breaks out a spot to connect 5V and GND and another spot to attach an external reset button (RST and GND). You do not need to connect these.
BOM:
This is just an adapter board. No components are required beyond the display and the D1 Mini.
Show full description
Allows you to easily attach a Wemos D1 Mini to a 2.8" or 3.2" with a 14 Pin Header. Examples of these displays can be found here (3.2") and here (2.4"). Many other vendors sell them as well.
Th…
Allows you to easily attach a Wemos D1 Mini to a 2.8" or 3.2" with a 14 Pin Header. Examples of these displays can be found here (3.2") and here (2.4"). Many other vendors sell them as well.
The pins on the display header are connected to the pins on the D1 Mini as follows:
| TFT Pin |
Name |
D1 Pin |
| 1 |
T_IRQ |
D1 |
| 2 |
T_DO |
D6 |
| 3 |
T_DIN |
D7 |
| 4 |
T_CS |
D2 |
| 5 |
T_CLK |
D5 |
| 6 |
SDO (MISO) |
D6 |
| 7 |
LED |
D0 |
| 8 |
SCK |
D5 |
| 9 |
SDI (MOSI) |
D7 |
| 10 |
DC |
D4 |
| 11 |
RESET |
3V3 |
| 12 |
CS |
D8 |
| 13 |
GND |
G |
| 14 |
VCC |
3V3 |
Note: The LED pin controls the brightness of the display backlight. It is connected to D0 on the D1 Mini, so your code will need to set that HIGH for full brightness, or PWM it for dimmer values.
The board also breaks out a spot to connect 5V and GND and another spot to attach an external reset button (RST and GND). You do not need to connect these.
BOM:
This is just an adapter board. No components are required beyond the display and the D1 Mini.
Show full description
