Shared Projects by Red

Shared Projects by Red

[OUTDATED] Firmware Developers Only - 17mm DD+7135

Top
Bottom

2 layer board of 0.67 x 0.67 inches (17.0 x 17.0 mm)
Uploaded: August 06, 2014
Shared: August 06, 2014
Total Price: $2.20

If you can't figure out the component placements on a completely unlabeled board, this is not for you. This board does not have a firmware available. This board is untested. This board does not have the [June/July 2014] anti-boost fix incorporated, MCU voltage may go too high. Any silkscreen …

Show full description

If you can't figure out the component placements on a completely unlabeled board, this is not for you. This board does not have a firmware available. This board is untested. This board does not have the [June/July 2014] anti-boost fix incorporated, MCU voltage may go too high. Any silkscreen …

Show full description

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

[outdated] 22mm 7135 v016

Top
Bottom

2 layer board of 0.88 x 0.88 inches (22.3 x 22.3 mm)
Uploaded: July 18, 2014
Shared: July 18, 2014
Total Price: $3.80

Replacement: https://oshpark.com/shared_projects/FQYMvlPm

0805 sized resistors & caps.

Standard Nanjg 105c components: 19.1k/4.7k resistors, C1, D1, etc.

Standard Zener setup: Replace D1 w/ 200-ohm or otherwise appropriate resistor. Populat…

Show full description

Replacement: https://oshpark.com/shared_projects/FQYMvlPm

0805 sized resistors & caps.

Standard Nanjg 105c components: 19.1k/4.7k resistors, C1, D1, etc.

Standard Zener setup: Replace D1 w/ 200-ohm or otherwise appropriate resistor. Populat…

Show full description

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

PIC to ATTINY v07 - LD29

Top
Bottom

2 layer board of 0.26 x 0.32 inches (6.7 x 8.0 mm)
Uploaded: July 10, 2014
Shared: July 10, 2014
Total Price: $0.40

Revised for use with an LD29 driver.

http://budgetlightforum.com/node/32648#comment-611634 (post#27)

Revised for use with an LD29 driver.

http://budgetlightforum.com/node/32648#comment-611634 (post#27)

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

26mm contact board v14

Top
Bottom

2 layer board of 1.03 x 1.03 inches (26.1 x 26.1 mm)
Uploaded: July 09, 2014
Shared: July 09, 2014
Total Price: $5.25

Bugfix over v13. Intended to be filed while spun on a 1/16in mandrel. Otherwise similar to v11: 16mm tabs for 17mm driver or file to the outside of the purple line to get a 18.08mm circle for a 20mm driver. Additional 0.2mm purple lines at 22mm and 24mm for cutting board down. Both sides have a …

Show full description

Bugfix over v13. Intended to be filed while spun on a 1/16in mandrel. Otherwise similar to v11: 16mm tabs for 17mm driver or file to the outside of the purple line to get a 18.08mm circle for a 20mm driver. Additional 0.2mm purple lines at 22mm and 24mm for cutting board down. Both sides have a …

Show full description

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

PIC to ATTINY v06

Top
Bottom

2 layer board of 0.26 x 0.32 inches (6.7 x 8.0 mm)
Uploaded: July 08, 2014
Shared: July 08, 2014
Total Price: $0.40

revised to stack rather than mirror the bottom (oops!)

revised to stack rather than mirror the bottom (oops!)

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project
Whaleshark white
© Copyright 2024 OSH Park, LLC | Privacy