Shared projects

S/PDIF Optical Audio Output for Teensy 3.1

2 layer board of 0.55 x 0.70 inches (14.0 x 17.9 mm).
Shared on May 21st, 2015 11:16

S/PDIF optical output for Teensy 3.1.

Parts Required:

  Everlight PLT133/T6A connector, Digikey 1080-1434-ND
  Capacitor, 0.1 uF, 0805 size, Digikey 1276-1003-1-ND

The Teensy Audio library now officially supports S/PDIF output. WAV File Player Example (in Arduino: File > Examples > Audio > WavFilePlayer) has been updated to show how to use it.

The S/PDIF output object is now available in the Audio System Design Tool, so you can easily create arbitrarily complex audio projects with digital S/PDIF output.

Special thanks to Frank Boesing for developing the S/PDIF encoding code!

Ongoing development conversation here:

The S/PDIF signal is output on pin 22. An inexpensive connector (Digikey 1080-1434-ND), or simply a red LED, can be used to couple the digital audio to an optical TOSLINK cable! Resistors and a small transformer can also be used, for non-optical RCA connector S/PDIF.


S/PDIF Optical Audio Output for Teensy 3.1

2 layer board of 0.55 x 0.70 inches (14.0 x 17.9 mm).
Shared on May 21st, 2015 11:16

S/PDIF optical output for Teensy 3.1.

Parts Required:

  Everlight PLT133/T6A connector, Digikey 1080-1434-ND
  Capacitor, 0.1 uF, 0805 size, Digikey 1276-1003-1-ND

The Teensy Audio library now officially supports S/PDIF output. WAV File Player Example (in Arduino: File > Examples > Audio > WavFilePlayer) has been updated to show how to use it.

The S/PDIF output object is now available in the Audio System Design Tool, so you can easily create arbitrarily complex audio projects with digital S/PDIF output.

Special thanks to Frank Boesing for developing the S/PDIF encoding code!

Ongoing development conversation here:

The S/PDIF signal is output on pin 22. An inexpensive connector (Digikey 1080-1434-ND), or simply a red LED, can be used to couple the digital audio to an optical TOSLINK cable! Resistors and a small transformer can also be used, for non-optical RCA connector S/PDIF.



ILI9431 Display (320x240) to Teensy 3.1

2 layer board of 1.80 x 1.48 inches (45.8 x 37.5 mm).
Shared on May 12th, 2015 13:53

This is the little test board shown here:

http://www.pjrc.com/store/display_ili9341.html

Parts used on the board are:

    LM7805 voltage regulator        Digikey LM7805ACT-ND
    B130 Schottky diode             Digikey B130-FDICT-ND
    140 mA PTC fuse                 Digikey 507-1495-1-ND
    100 ohm 1/4 watt resistor       Digikey 100XBK-ND
    DC power jack                   Mouser 163-7620E-E
    1uF 0805 capacitor              Digikey 1276-1066-1-ND

Component Placement

An older version of this board had a minor error. You can easily identify the board version by the location of the 100 ohm resistor.


ILI9431 Display (320x240) to Teensy 3.1

2 layer board of 1.80 x 1.48 inches (45.8 x 37.5 mm).
Shared on May 12th, 2015 13:53

This is the little test board shown here:

http://www.pjrc.com/store/display_ili9341.html

Parts used on the board are:

    LM7805 voltage regulator        Digikey LM7805ACT-ND
    B130 Schottky diode             Digikey B130-FDICT-ND
    140 mA PTC fuse                 Digikey 507-1495-1-ND
    100 ohm 1/4 watt resistor       Digikey 100XBK-ND
    DC power jack                   Mouser 163-7620E-E
    1uF 0805 capacitor              Digikey 1276-1066-1-ND

Component Placement

An older version of this board had a minor error. You can easily identify the board version by the location of the 100 ohm resistor.



zooplankton1

2 layer board of 1.70 x 1.75 inches (43.2 x 44.5 mm).
Shared on April 7th, 2015 23:42

10 watt LED driver board with DMX protocol input and 8 bit control to gamma corrected brightness.


zooplankton1

2 layer board of 1.70 x 1.75 inches (43.2 x 44.5 mm).
Shared on April 7th, 2015 23:42

10 watt LED driver board with DMX protocol input and 8 bit control to gamma corrected brightness.



miditest2

2 layer board of 2.25 x 1.35 inches (57.2 x 34.4 mm).
Shared on September 8th, 2014 19:05

miditest2


miditest2

2 layer board of 2.25 x 1.35 inches (57.2 x 34.4 mm).
Shared on September 8th, 2014 19:05

miditest2



ILI9431 Display (320x240) to Teensy 3.1

2 layer board of 1.80 x 1.48 inches (45.8 x 37.5 mm).
Shared on August 29th, 2014 19:32

Newer Version Available

A new version of this board is available. It fixes problems with the reset signal and power jack.

You can easily identify the board version by the location of the 100 ohm resistor.

Old Info:

This is the little test board shown here:

http://www.pjrc.com/store/display_ili9341.html

Parts used on the board are:

    LM7805 voltage regulator        Digikey LM7805ACT-ND
    B130 Schottky diode             Digikey B130-FDICT-ND
    140 mA PTC fuse                 Digikey 507-1495-1-ND
    100 ohm 1/4 watt resistor       Digikey 100XBK-ND
    DC power jack                   Mouser 163-7620E-E
    1uF 0805 capacitor              Digikey 1276-1066-1-ND

Component Placement

This PCB has the display RST signals connected to pin 8, not 3.3V. This special step is needed to make it work.


ILI9431 Display (320x240) to Teensy 3.1

2 layer board of 1.80 x 1.48 inches (45.8 x 37.5 mm).
Shared on August 29th, 2014 19:32

Newer Version Available

A new version of this board is available. It fixes problems with the reset signal and power jack.

You can easily identify the board version by the location of the 100 ohm resistor.

Old Info:

This is the little test board shown here:

http://www.pjrc.com/store/display_ili9341.html

Parts used on the board are:

    LM7805 voltage regulator        Digikey LM7805ACT-ND
    B130 Schottky diode             Digikey B130-FDICT-ND
    140 mA PTC fuse                 Digikey 507-1495-1-ND
    100 ohm 1/4 watt resistor       Digikey 100XBK-ND
    DC power jack                   Mouser 163-7620E-E
    1uF 0805 capacitor              Digikey 1276-1066-1-ND

Component Placement

This PCB has the display RST signals connected to pin 8, not 3.3V. This special step is needed to make it work.