Arch Series LED Driver v2
2 layer board of 3.02 x 3.02 inches (76.7 x 76.7 mm)
Uploaded:
June 21, 2021
Shared:
June 21, 2021
Total Price:
$45.60
4 Channel Parallel Output Radial LED controller for 3 wire addressable LEDs using a Wemos D1 mini. Designed specifically for a series of LED sculptures created in the winter/spring of 2021. This board was updated in June 2021 to remove potential issues when soldering the resistors, causing a shor…
Show full description
4 Channel Parallel Output Radial LED controller for 3 wire addressable LEDs using a Wemos D1 mini. Designed specifically for a series of LED sculptures created in the winter/spring of 2021. This board was updated in June 2021 to remove potential issues when soldering the resistors, causing a shor…
Show full description
Teensy 4.0 16 Channel Parallel Output for FastLED
2 layer board of 3.63 x 2.19 inches (92.1 x 55.6 mm)
Uploaded:
October 20, 2019
Shared:
October 22, 2019
Total Price:
$39.65
This board makes easy use of FastLED's powerful parallel output method to drive multiple Neopixel LED(WS2811, WS2812, WS2812B, SK6812, etc) channels. It is designed for the Teensy 4.0 to convert the Teensy's 3v signals to 5v for the Neopixels. The signals for the Neopixels are terminated at screw…
Show full description
This board makes easy use of FastLED's powerful parallel output method to drive multiple Neopixel LED(WS2811, WS2812, WS2812B, SK6812, etc) channels. It is designed for the Teensy 4.0 to convert the Teensy's 3v signals to 5v for the Neopixels. The signals for the Neopixels are terminated at screw…
Show full description
Teensy 4.0 to WS2811Octo Adaptor
2 layer board of 0.82 x 1.44 inches (20.9 x 36.6 mm)
Uploaded:
October 22, 2019
Shared:
October 22, 2019
Total Price:
$5.90
WARNING: This board has not yet been tested!!! Order at your own risk. I am awaiting shipment and will update when received.
This board serves as a pin reroute for the Teensy 4.0 to utilize the WS2811Octo Adaptor, both created by PJRC. The new parallel output pins are as follows: 19,18,1…
Show full description
WARNING: This board has not yet been tested!!! Order at your own risk. I am awaiting shipment and will update when received.
This board serves as a pin reroute for the Teensy 4.0 to utilize the WS2811Octo Adaptor, both created by PJRC. The new parallel output pins are as follows: 19,18,1…
Show full description
2S_redhat_AV_sensor_board_gndPlane
2 layer board of 3.06 x 2.53 inches (77.8 x 64.1 mm)
Uploaded:
April 12, 2019
Shared:
April 27, 2019
Total Price:
$38.65
Audio Visual board for RedHat Summit 2019. More details to come
Audio Visual board for RedHat Summit 2019. More details to come
Teensy 3.2 based RJ45 Stepper Control
2 layer board of 1.89 x 2.55 inches (48.0 x 64.8 mm)
Uploaded:
March 12, 2018
Shared:
March 13, 2018
Total Price:
$24.05
This is the control board for 8 stepper motors. Each RJ45 connector supplies GND, Step, Direction, and a signal line from a limit switch at the motor. Each motor driver is attached to the motor. Using ethernet cables to easily transfer data signals from Teensy to motor drivers.
This is the control board for 8 stepper motors. Each RJ45 connector supplies GND, Step, Direction, and a signal line from a limit switch at the motor. Each motor driver is attached to the motor. Using ethernet cables to easily transfer data signals from Teensy to motor drivers.
