Shared Projects by HighInBC

Shared Projects by HighInBC

Micro beeper.kicad_pcb

Top
Bottom

2 layer board of 0.47 x 0.47 inches (12.0 x 12.0 mm)
Uploaded: August 06, 2022
Shared: August 06, 2022
Total Price: $1.10

Tiny transistor backpack for beeper.

BOM:

  • BC817 SOT-23
  • Approx 2.1k 0603 resistor
  • 12mm active 5V beeper

Attach 5V to +, GND to -, and signal to B.

Tiny transistor backpack for beeper.

BOM:

  • BC817 SOT-23
  • Approx 2.1k 0603 resistor
  • 12mm active 5V beeper

Attach 5V to +, GND to -, and signal to B.

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

50mA dummy load

Top
Bottom

2 layer board of 0.40 x 0.63 inches (10.2 x 15.9 mm)
Uploaded: July 11, 2016
Shared: December 11, 2021
Total Price: $1.25

To stop my USB power bank from turning itself off

To stop my USB power bank from turning itself off

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

Fermentation box wiring harness

Top
Bottom

2 layer board of 1.08 x 1.14 inches (27.5 x 29.0 mm)
Uploaded: May 09, 2017
Shared: December 22, 2018
Total Price: $6.15

Rev H

Rev H

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

50mA USB dummy load Rev B

Top
Bottom

2 layer board of 0.40 x 0.63 inches (10.2 x 15.9 mm)
Uploaded: August 02, 2016
Shared: October 04, 2018
Total Price: $1.25

To stop my USB battery from turning off

To stop my USB battery from turning off

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project

GRBL nano to DB25

Top
Bottom

2 layer board of 1.64 x 1.06 inches (41.6 x 27.0 mm)
Uploaded: October 07, 2017
Shared: October 07, 2017
Total Price: $8.70

NOT YET TESTED

Allows you to connect a GRBL arduino nano based controller to a parallel port based CNC. The pin mapping is specific to my cheap Chinese CNC router. It may match yours, it may not.

Schematic

BoM

  • 1 arduino nano

…

Show full description

NOT YET TESTED

Allows you to connect a GRBL arduino nano based controller to a parallel port based CNC. The pin mapping is specific to my cheap Chinese CNC router. It may match yours, it may not.

Schematic

BoM

  • 1 arduino nano

…

Show full description

Top
Bottom
  • Actions

      Ordering shared project

      Hey there! Before ordering, make sure you have all the info you need to complete and use this design. This usually means a component list, and sometimes additional information such as assembly notes, source code, or usage guides.
      Since this is a project designed by a community member, it may contain design errors that prevent it from working as intended. OSH Park cannot place any guarantees about the functionality or correctness of the design.
      Order Board
    • Order Board
    • Download
    • Permalink
    • Embed link
Embeddable link to order this shared Project
Whaleshark white
© Copyright 2025 OSH Park, LLC | Privacy