8-Bit Shift Register
author: brodyf42
2 layer board of 0.85 x 0.90 inches (21.6 x 22.9 mm)
Uploaded:
February 11, 2014
Shared:
February 11, 2014
Total Price:
$3.80
This is a chainable 8-Bit serial-in / parallel-out shift register based on the 74HC164 IC. Be aware that the reset is actve LOW.
This is a chainable 8-Bit serial-in / parallel-out shift register based on the 74HC164 IC. Be aware that the reset is actve LOW.
ATTiny XBee Connected I2C / Analog Sensor
author: chipmc
2 layer board of 2.35 x 1.25 inches (59.7 x 31.8 mm)
Uploaded:
January 28, 2014
Shared:
February 11, 2014
Total Price:
$14.70
Tested - Works!
General Purpose I2C and Analog Wireless Sensor Board. This board supports an I2C and a Digital / Analog sensor connection and the ability to communicate readings using an XBee radio.
Tested - Works!
General Purpose I2C and Analog Wireless Sensor Board. This board supports an I2C and a Digital / Analog sensor connection and the ability to communicate readings using an XBee radio.
Power Supply: AC Mains to Low Voltage DC
author: Eric
2 layer board of 1.63 x 2.30 inches (41.4 x 58.3 mm)
Uploaded:
January 15, 2014
Shared:
February 10, 2014
Total Price:
$18.70
Cost: $18.70 for three.
Description:
I needed a low voltage, low current DC power supply for a mains-powered project but I was out of spare wall warts, so I whipped this together and it does the job nicely.
Holes along the edges of the board are sized for [M3 x 4mm stando…
Show full description
Cost: $18.70 for three.
Description:
I needed a low voltage, low current DC power supply for a mains-powered project but I was out of spare wall warts, so I whipped this together and it does the job nicely.
Holes along the edges of the board are sized for [M3 x 4mm stando…
Show full description
CRAMPS V1.0
author: cdsteinkuehler
2 layer board of 3.92 x 4.02 inches (99.4 x 102.0 mm)
Uploaded:
February 10, 2014
Shared:
February 10, 2014
Total Price:
$78.55
3D printing cape for the BeagleBone, based on the RAMPS-FD design for the Due. Details Source Files
3D printing cape for the BeagleBone, based on the RAMPS-FD design for the Due. Details Source Files
RS232 for Electric Imp BreakOut Board
author: ljbeng
2 layer board of 1.19 x 1.26 inches (30.2 x 32.0 mm)
Uploaded:
February 09, 2014
Shared:
February 10, 2014
Total Price:
$7.50
This will solder directly to the SparkFun Electric Imp breakout https://www.sparkfun.com/products/11400 and adds RS232 Serial voltage levels to the Imp. Power and serial are all through an RJ12 6 pin connector. 1-GND, 2-+5V, 3-Tx232, 4-Rx232. Uses Uart57 on Imp. Chip is Max3232 http://www….
Show full description
This will solder directly to the SparkFun Electric Imp breakout https://www.sparkfun.com/products/11400 and adds RS232 Serial voltage levels to the Imp. Power and serial are all through an RJ12 6 pin connector. 1-GND, 2-+5V, 3-Tx232, 4-Rx232. Uses Uart57 on Imp. Chip is Max3232 http://www….
Show full description
MAX21100 V3 Breakout
author: SpaceCoaster
2 layer board of 0.61 x 0.61 inches (15.6 x 15.6 mm)
Uploaded:
February 09, 2014
Shared:
February 09, 2014
Total Price:
$1.85
Type 5 Comparator
author: tricorderproject
2 layer board of 1.58 x 0.78 inches (40.0 x 19.8 mm)
Uploaded:
February 09, 2014
Shared:
February 09, 2014
Total Price:
$6.10
External comparator for Radiation Watch Type 5 Detector
External comparator for Radiation Watch Type 5 Detector
Spark Core Programmer Shield
author: robertdolca
2 layer board of 2.50 x 1.55 inches (63.5 x 39.4 mm)
Uploaded:
February 09, 2014
Shared:
February 09, 2014
Total Price:
$19.35
BITX Amplifier Block
author: roamingryan
2 layer board of 1.00 x 1.00 inches (25.4 x 25.4 mm)
Uploaded:
February 09, 2014
Shared:
February 09, 2014
Total Price:
$5.00
General purpose bidirectional amplifier
General purpose bidirectional amplifier
Robotic Arm Servo Controller
author: Josh-Jetter
2 layer board of 2.32 x 1.92 inches (58.8 x 48.7 mm)
Uploaded:
February 08, 2014
Shared:
February 08, 2014
Total Price:
$22.15
Servo mechanism controller for a brushed DC motor
Servo mechanism controller for a brushed DC motor