Mini OLED breakout
author: Zephod
2 layer board of 0.50 x 0.46 inches (12.6 x 11.7 mm)
Uploaded:
December 25th 2013
Shared:
December 25th 2013
Total Price:
$1.10
Small breakout protoboard for -> http://www.buydisplay.com/default/mp3-oled.html
using the built in regulator. Pins/caps should be reasonably obvious if you compare it to the schematic in the "interface" datasheet. Untested so far.
Small breakout protoboard for -> http://www.buydisplay.com/default/mp3-oled.html
using the built in regulator. Pins/caps should be reasonably obvious if you compare it to the schematic in the "interface" datasheet. Untested so far.
utftlib1
author: PaulStoffregen
2 layer board of 2.11 x 1.28 inches (53.5 x 32.4 mm)
Uploaded:
December 23rd 2013
Shared:
December 24th 2013
Total Price:
$13.40
The easy way to connect 8 or 16 bit parallel TFT displays to a Teensy 3.x board.
The easy way to connect 8 or 16 bit parallel TFT displays to a Teensy 3.x board.
PowerBarB2
author: AndiceLabs
2 layer board of 0.83 x 2.15 inches (21.1 x 54.7 mm)
Uploaded:
December 2nd 2013
Shared:
December 23rd 2013
Total Price:
$8.90
A BeagleBone power supply for battery use. For more information see this page.
A BeagleBone power supply for battery use. For more information see this page.
RectDoubleLongSimple-2013-12-22-15-
author: dr2chase
2 layer board of 2.84 x 0.87 inches (72.0 x 22.0 mm)
Uploaded:
December 22nd 2013
Shared:
December 22nd 2013
Total Price:
$12.25
Modified Greinacher doubler, skinny. Intended to convert bicycle "generator" (sidewall or hub) to LED current. Recommend four SB540 diodes, two 1mF x 16V laid down on board, one 6.8mF x 35V at end. Be aware of dimensions to be sure it will fit in desired tube. Use painter's tape to make mo…
Show full description
Modified Greinacher doubler, skinny. Intended to convert bicycle "generator" (sidewall or hub) to LED current. Recommend four SB540 diodes, two 1mF x 16V laid down on board, one 6.8mF x 35V at end. Be aware of dimensions to be sure it will fit in desired tube. Use painter's tape to make mo…
Show full description
CycloneGRBLControl
author: secures
2 layer board of 3.22 x 2.71 inches (81.8 x 68.8 mm)
Uploaded:
December 22nd 2013
Shared:
December 22nd 2013
Total Price:
$43.55
CNC ControlBoard for Cyclone-PCB-Factory (GRBL compatilble)
CNC ControlBoard for Cyclone-PCB-Factory (GRBL compatilble)
Sparkfun 6" 7 Segment Breakout (Conventional)
author: Damage
2 layer board of 1.95 x 1.73 inches (49.5 x 43.9 mm)
Uploaded:
December 21st 2013
Shared:
December 21st 2013
Total Price:
$16.85
A Breakout board so that the 6" Sparkfun 7 Segment displays can be "Daisy Chained" Uses Shift Registers in an "Open Drain" configuration. This is the Conventional Version (Decimal Point at the bottom Right)
A Breakout board so that the 6" Sparkfun 7 Segment displays can be "Daisy Chained" Uses Shift Registers in an "Open Drain" configuration. This is the Conventional Version (Decimal Point at the bottom Right)
Sparkfun 6" 7 Segment Breakout (Inverted)
author: Damage
2 layer board of 1.95 x 1.73 inches (49.5 x 43.9 mm)
Uploaded:
December 21st 2013
Shared:
December 21st 2013
Total Price:
$16.85
A Breakout board so that the 6" Sparkfun 7 Segment displays can be "Daisy Chained" Uses Shift Registers in an "Open Drain" configuration. This is the Inverted Version (Decimal Point at the top left)
A Breakout board so that the 6" Sparkfun 7 Segment displays can be "Daisy Chained" Uses Shift Registers in an "Open Drain" configuration. This is the Inverted Version (Decimal Point at the top left)
LED & Button Breakout v1.1
author: heckler95
2 layer board of 2.15 x 0.90 inches (54.7 x 22.9 mm)
Uploaded:
December 19th 2013
Shared:
December 19th 2013
Total Price:
$9.65
Breakout board with 6 through-hole momentary pushbuttons and 6 1206 SMD LEDs. Also includes 0805 SMD pull-up resistors for the buttons and current-limiting resistors for the LEDs. UNTESTED DESIGN
Breakout board with 6 through-hole momentary pushbuttons and 6 1206 SMD LEDs. Also includes 0805 SMD pull-up resistors for the buttons and current-limiting resistors for the LEDs. UNTESTED DESIGN
DS1307 Breakout v2.0
author: heckler95
2 layer board of 1.20 x 1.05 inches (30.5 x 26.7 mm)
Uploaded:
September 11th 2013
Shared:
December 19th 2013
Total Price:
$6.30
DS1307 Real-time Clock IC breakout board for easily incorporating a DS1307 into your breadboard projects. This is my first attempt at board design. I have built and tested all 3 copies from my order and they all work great.
DS1307 Real-time Clock IC breakout board for easily incorporating a DS1307 into your breadboard projects. This is my first attempt at board design. I have built and tested all 3 copies from my order and they all work great.
Lorenz Attractor
author: Quim
2 layer board of 2.00 x 1.04 inches (50.8 x 26.3 mm)
Uploaded:
November 25th 2013
Shared:
December 19th 2013
Total Price:
$10.35
This is an implementation of the circuit suggested in http://frank.harvard.edu/~paulh/misc/lorenz.htm that models the Lorenz equations.
This is an implementation of the circuit suggested in http://frank.harvard.edu/~paulh/misc/lorenz.htm that models the Lorenz equations.