Aquarium Control v2.5
2 layer board of 1.72 x 1.26 inches (43.6 x 31.9 mm)
Uploaded:
July 16, 2013
Shared:
August 03, 2014
Total Price:
$10.75
Originally intended to control the lights of an aquarium, this board takes two 3.3V inverted logic inputs and drives two relays for powering up to 1.5A loads (give or take). The board requires 10VDC to 40VDC power to power the relay logic. For more details, read my blog post about the [hardware s…
Show full description
Originally intended to control the lights of an aquarium, this board takes two 3.3V inverted logic inputs and drives two relays for powering up to 1.5A loads (give or take). The board requires 10VDC to 40VDC power to power the relay logic. For more details, read my blog post about the [hardware s…
Show full description
RasPi PCM3060 Shield
author: jronen
2 layer board of 1.76 x 1.76 inches (44.6 x 44.6 mm)
Uploaded:
July 02, 2014
Shared:
August 03, 2014
Total Price:
$15.40
A raspberry pi shield that provides high quality, 24-bit DAC and ADC at 48KHz.
Schematics can be found at https://github.com/jonronen/geda-stuff/tree/master/audio_shield/pcm3060_rpi
Kernel sources can be found at https://github.com/jonronen/raspi-linux
Based on work by Florian Meier: htt…
Show full description
A raspberry pi shield that provides high quality, 24-bit DAC and ADC at 48KHz.
Schematics can be found at https://github.com/jonronen/geda-stuff/tree/master/audio_shield/pcm3060_rpi
Kernel sources can be found at https://github.com/jonronen/raspi-linux
Based on work by Florian Meier: htt…
Show full description
bGeigieNano+
author: FlorinC
2 layer board of 4.13 x 2.63 inches (104.8 x 66.7 mm)
Uploaded:
August 03, 2014
Shared:
August 03, 2014
Total Price:
$54.10
bGeigieNano upgraded with ATmega644/1284 processor
bGeigieNano upgraded with ATmega644/1284 processor
MicroTProbe v0.2
author: sirkha
2 layer board of 0.26 x 0.56 inches (6.6 x 14.2 mm)
Uploaded:
August 03, 2014
Shared:
August 03, 2014
Total Price:
$0.70
A breakout for the [TMP102] [1] from Texas Instruments small enough to fit inside a ¼ inch copper tube. This was inspired by the [SparkFun breakout board] [2] for the same chip.
This is designed to be used with ¼ inch copper tube and thermal putty to create a water-sealed temperature probe…
Show full description
A breakout for the [TMP102] [1] from Texas Instruments small enough to fit inside a ¼ inch copper tube. This was inspired by the [SparkFun breakout board] [2] for the same chip.
This is designed to be used with ¼ inch copper tube and thermal putty to create a water-sealed temperature probe…
Show full description
ATTinyX5_Breakout
author: ManiacalLabs
2 layer board of 0.52 x 0.63 inches (13.3 x 16.1 mm)
Uploaded:
August 03, 2014
Shared:
August 03, 2014
Total Price:
$1.65
6 Channel LED Driver
author: AtticusG3
4 layer board of 2.40 x 1.55 inches (61.0 x 39.4 mm)
Uploaded:
August 03, 2014
Shared:
August 03, 2014
Total Price:
$37.20
> # Alpha prototype stage. #
>This board uses an onboard Atmega328p to drive 6 N-Channel Mosfets with it's PWM pins.
>D2, D4, A0 and A1 are broken out along with GND 5v and Vin to a 2x5 header designed to run an external switch panel.
>ISCP pins are also broken out to allow in-situ progr…
Show full description
> # Alpha prototype stage. #
>This board uses an onboard Atmega328p to drive 6 N-Channel Mosfets with it's PWM pins.
>D2, D4, A0 and A1 are broken out along with GND 5v and Vin to a 2x5 header designed to run an external switch panel.
>ISCP pins are also broken out to allow in-situ progr…
Show full description
msop-dip
author: voltergeist
2 layer board of 0.41 x 0.58 inches (10.3 x 14.6 mm)
Uploaded:
May 13, 2014
Shared:
August 02, 2014
Total Price:
$1.15
msop10
msop10
50pin IDC to Breadboard adapter
author: stefanberndtsson
2 layer board of 4.85 x 0.78 inches (123.1 x 19.8 mm)
Uploaded:
August 02, 2014
Shared:
August 02, 2014
Total Price:
$18.85
Adapter for connecting a 50pin IDC connector to a breadboard with offset so that the breadboard isn't covered by the ribbon cable
Adapter for connecting a 50pin IDC connector to a breadboard with offset so that the breadboard isn't covered by the ribbon cable
Audioleveler by W2AEW (C4, new value)
author: LRY
2 layer board of 0.79 x 1.85 inches (20.0 x 47.0 mm)
Uploaded:
August 02, 2014
Shared:
August 02, 2014
Total Price:
$7.25
Audio limiter/leveler by W2AEW, checkout his YouTubechannel for more: https://www.youtube.com/channel/UCiqd3GLTluk2s_IBt7p_LjA
Audio limiter/leveler by W2AEW, checkout his YouTubechannel for more: https://www.youtube.com/channel/UCiqd3GLTluk2s_IBt7p_LjA
LSM9DS0+MS5611Teensy3.1Add-On.v01
2 layer board of 0.71 x 0.51 inches (17.9 x 13.0 mm)
Uploaded:
August 02, 2014
Shared:
August 02, 2014
Total Price:
$1.80
LSM9DS0 9-axis motion sensor plus MS5611 pressure sensor/altimeter add-on board for Teensy 3.1 hardwired for I2C
LSM9DS0 9-axis motion sensor plus MS5611 pressure sensor/altimeter add-on board for Teensy 3.1 hardwired for I2C
FreHD Eagle Version
author: fbelavenuto
2 layer board of 3.80 x 3.20 inches (96.6 x 81.2 mm)
Uploaded:
August 01, 2014
Shared:
August 01, 2014
Total Price:
$60.75
FreHD Eagle Version. Documentation: https://drive.google.com/file/d/0B5wpc_jDN_n0Z1A0TmtIcGhyM1E/edit?usp=sharing https://github.com/fbelavenuto/frehd-br
FreHD Eagle Version. Documentation: https://drive.google.com/file/d/0B5wpc_jDN_n0Z1A0TmtIcGhyM1E/edit?usp=sharing https://github.com/fbelavenuto/frehd-br
MAX31850K Breakout v1.0
author: nslogan
2 layer board of 0.85 x 0.85 inches (21.6 x 21.6 mm)
Uploaded:
August 01, 2014
Shared:
August 01, 2014
Total Price:
$3.60
A small breakout board for the Maxim MAX31850K 1-wire type-K thermocouple amplifier with CJC. Project available on GitHub.
A small breakout board for the Maxim MAX31850K 1-wire type-K thermocouple amplifier with CJC. Project available on GitHub.
