Shared Projects

Shared Projects

Transceiver Module 1.2

author: PhracturedBlue

2 layer board of 0.92 x 1.86 inches (23.3 x 47.1 mm)
Uploaded: February 15th 2014
Shared: February 15th 2014
Total Price: $8.50

DeviationTX.com

DeviationTX.com

Embeddable link to order this shared Project

Joule Thief revision 3

author: Warhawk

2 layer board of 0.98 x 0.96 inches (24.8 x 24.4 mm)
Uploaded: February 15th 2014
Shared: February 15th 2014
Total Price: $4.65

http://www.circuitstew.com/pcbs/joule_thief.html

http://www.circuitstew.com/pcbs/joule_thief.html

Embeddable link to order this shared Project

FPV car rx

author: rudyauction509

2 layer board of 2.94 x 1.99 inches (74.8 x 50.6 mm)
Uploaded: February 7th 2014
Shared: February 15th 2014
Total Price: $29.35

microcontrollers: pic16f630, 'out' is an aux output port not a chip. crystals: 20mhz

http://www.rcgroups.com/forums/showthread.php?t=2102301

microcontrollers: pic16f630, 'out' is an aux output port not a chip. crystals: 20mhz

http://www.rcgroups.com/forums/showthread.php?t=2102301

Embeddable link to order this shared Project

FPV car tx 16f819

author: rudyauction509

2 layer board of 2.57 x 1.26 inches (65.2 x 31.9 mm)
Uploaded: February 8th 2014
Shared: February 15th 2014
Total Price: $16.10

v1.0, microcontroller: 16f819,

http://www.rcgroups.com/forums/showthread.php?t=2102301

v1.0, microcontroller: 16f819,

http://www.rcgroups.com/forums/showthread.php?t=2102301

Embeddable link to order this shared Project

bike light

author: rudyauction509

2 layer board of 1.36 x 1.21 inches (34.4 x 30.6 mm)
Uploaded: January 31st 2014
Shared: February 15th 2014
Total Price: $8.15

Simple bike taillight for pic16f630, R9 is 1k, all others 100 ohm. Use 5mm LEDs of your choice, I used red and green flashing alternately. Runs on 3x AA or AAA cells or 1x Li-Ion cell, no regulator so don't feed over 5.5 volts.

Simple bike taillight for pic16f630, R9 is 1k, all others 100 ohm. Use 5mm LEDs of your choice, I used red and green flashing alternately. Runs on 3x AA or AAA cells or 1x Li-Ion cell, no regulator so don't feed over 5.5 volts.

Embeddable link to order this shared Project

Li-ion Charger revision v1.0

author: NickLeijenhorst

2 layer board of 0.87 x 1.50 inches (22.0 x 38.0 mm)
Uploaded: February 14th 2014
Shared: February 14th 2014
Total Price: $6.45

  • Charges a 1-cell Li-ion battery through mini-USB or another input (3.75v - 6v)

  • Charging current selectable through a solder jumper

  • Big solder pads for input and output

  • Status led to indicate charging (5 mA)

  • Charges a 1-cell Li-ion battery through mini-USB or another input (3.75v - 6v)

  • Charging current selectable through a solder jumper

  • Big solder pads for input and output

  • Status led to indicate charging (5 mA)

Embeddable link to order this shared Project

Lichtsteuerung

author: Felicitus

2 layer board of 6.21 x 3.40 inches (157.7 x 86.4 mm)
Uploaded: February 14th 2014
Shared: February 14th 2014
Total Price: $105.60

Embeddable link to order this shared Project

Tinusaur Proto S v0.1 m1

author: boyanov

2 layer board of 0.80 x 1.00 inches (20.4 x 25.5 mm)
Uploaded: February 13th 2014
Shared: February 14th 2014
Total Price: $4.00

This is prototyping board for the Tinusaur project board.

The Tinusaur is a minimal micro-controller hardware configuration based on Atmel AVR ATtiny family of products and more specifically those with DIP-8 case such as ATtiny25/ATtiny45/ATtiny85, ATtiny13 as well as their variations.

The …

Show full description

This is prototyping board for the Tinusaur project board.

The Tinusaur is a minimal micro-controller hardware configuration based on Atmel AVR ATtiny family of products and more specifically those with DIP-8 case such as ATtiny25/ATtiny45/ATtiny85, ATtiny13 as well as their variations.

The …

Show full description

Embeddable link to order this shared Project

H-Bridge

author: Ritronic

2 layer board of 3.62 x 1.97 inches (92.0 x 50.0 mm)
Uploaded: February 14th 2014
Shared: February 14th 2014
Total Price: $35.65

High Speed / High Power H-Bridge with Current Sensing

High Speed / High Power H-Bridge with Current Sensing

Embeddable link to order this shared Project

ATTINY1634 A-DIP-TER

author: aberry

2 layer board of 1.00 x 0.82 inches (25.4 x 20.8 mm)
Uploaded: February 14th 2014
Shared: February 14th 2014
Total Price: $4.05

Breadboard-friendly ATTINY1634 dev board with xtal, ISP header, decoupling cap

Breadboard-friendly ATTINY1634 dev board with xtal, ISP header, decoupling cap

Embeddable link to order this shared Project

Level Shifter 002

author: rstraight

2 layer board of 3.65 x 2.29 inches (92.7 x 58.1 mm)
Uploaded: February 14th 2014
Shared: February 14th 2014
Total Price: $41.75

Bipolar to unipoar level converter

Bipolar to unipoar level converter

Embeddable link to order this shared Project

USB FPGA Breakout v2.0

author: jshamlet

4 layer board of 2.71 x 1.61 inches (68.7 x 40.8 mm)
Uploaded: July 24th 2013
Shared: February 13th 2014
Total Price: $43.40

Serial Breakout Board

Serial Breakout Board

Embeddable link to order this shared Project

USB FPGA v2.0

author: jshamlet

4 layer board of 2.76 x 1.66 inches (70.0 x 42.1 mm)
Uploaded: January 28th 2014
Shared: February 13th 2014
Total Price: $45.60

USB-enabled FPGA development board

USB-enabled FPGA development board

Embeddable link to order this shared Project

Spider Board

author: dwc238

2 layer board of 1.31 x 1.31 inches (33.2 x 33.2 mm)
Uploaded: February 13th 2014
Shared: February 13th 2014
Total Price: $8.50

Control Board for Spider Robot

Control Board for Spider Robot

Embeddable link to order this shared Project

BLF TINY10

author: Mattaus

2 layer board of 0.42 x 0.42 inches (10.6 x 10.6 mm)
Uploaded: February 13th 2014
Shared: February 13th 2014
Total Price: $0.85

10mm Nanjg 105C compatible LED/flashlight driver.

  • Diode D1 is a BAT54.
  • C1 is 10 uF.
  • Resistors are 19.1K and 4.7K, 1%
  • Regulator chips are AMC7135
  • Processor is ATTINY13 or similar

LED connects to the + and - holes.

Outer ring is ground. Battery plus connects to + from the re…

Show full description

10mm Nanjg 105C compatible LED/flashlight driver.

  • Diode D1 is a BAT54.
  • C1 is 10 uF.
  • Resistors are 19.1K and 4.7K, 1%
  • Regulator chips are AMC7135
  • Processor is ATTINY13 or similar

LED connects to the + and - holes.

Outer ring is ground. Battery plus connects to + from the re…

Show full description

Embeddable link to order this shared Project

j201 converter

author: Clayford

2 layer board of 0.30 x 0.27 inches (7.6 x 6.9 mm)
Uploaded: February 13th 2014
Shared: February 13th 2014
Total Price: $0.40

sot23 to-92 I did not design this, only shrink it as much as possible. Use resistor leads not SIL headers.

sot23 to-92 I did not design this, only shrink it as much as possible. Use resistor leads not SIL headers.

Embeddable link to order this shared Project

Dual 7 Segment Display

author: brodyf42

2 layer board of 0.94 x 0.88 inches (23.9 x 22.4 mm)
Uploaded: February 12th 2014
Shared: February 13th 2014
Total Price: $4.10

Embeddable link to order this shared Project

CC3000-Breakout-0805

author: james_littlefox

2 layer board of 1.15 x 0.80 inches (29.2 x 20.3 mm)
Uploaded: February 12th 2014
Shared: February 12th 2014
Total Price: $4.60

This is a modification of Kuy's CC3000 Breakout , the only difference is that this board uses all 0805 capacitors.

Source code at Github

This is a modification of Kuy's CC3000 Breakout , the only difference is that this board uses all 0805 capacitors.

Source code at Github

Embeddable link to order this shared Project

CAN module v0.1

author: rusefi

2 layer board of 0.92 x 0.44 inches (23.5 x 11.1 mm)
Uploaded: January 25th 2014
Shared: February 12th 2014
Total Price: $2.00

Embeddable link to order this shared Project

LTAR Minidisplay V4.5_0

author: thatdecade

2 layer board of 1.10 x 1.77 inches (28.0 x 45.0 mm)
Uploaded: February 12th 2014
Shared: February 12th 2014
Total Price: $9.75

LaserTag Display module for LTAR.

More info: http://gitlab.meldaire.net/izzy84075/ltar-minidisplay-releases/tree/master

LaserTag Display module for LTAR.

More info: http://gitlab.meldaire.net/izzy84075/ltar-minidisplay-releases/tree/master

Embeddable link to order this shared Project