[OUTDATED] Firmware Developers Only - 17mm DD+7135 v012
author: Red
2 layer board of 0.67 x 0.67 inches (17.0 x 17.0 mm)
Uploaded:
October 13, 2014
Shared:
October 13, 2014
Total Price:
$2.20
If you can’t figure out the component placements on a completely unlabeled board, this is not for you. This board does not have a firmware available. This board is untested. Any silkscreen markings are arbitrary and have no meaning.
This board requires a Power-SO8 footprint N-Channel FET suc…
Show full description
If you can’t figure out the component placements on a completely unlabeled board, this is not for you. This board does not have a firmware available. This board is untested. Any silkscreen markings are arbitrary and have no meaning.
This board requires a Power-SO8 footprint N-Channel FET suc…
Show full description
17dd_PIC_322 v1.0
author: Cereal_Killer
2 layer board of 0.67 x 0.67 inches (17.0 x 17.0 mm)
Uploaded:
October 13, 2014
Shared:
October 13, 2014
Total Price:
$2.20
17mm Direct Drive driver for the PIC 10F322 *see thread http://budgetlightforum.com/node/33927
- U1 is PIC 10F322
- D1 is SOT-323
- Z1 is SOT-123 (only populate if needed)
- C1 is 10uf 0805 X7R (for clicky builds using tterev3’s FW a resistor is stacked over the cap)
- FET is D2PAK such…
Show full description
17mm Direct Drive driver for the PIC 10F322 *see thread http://budgetlightforum.com/node/33927
- U1 is PIC 10F322
- D1 is SOT-323
- Z1 is SOT-123 (only populate if needed)
- C1 is 10uf 0805 X7R (for clicky builds using tterev3’s FW a resistor is stacked over the cap)
- FET is D2PAK such…
Show full description
Atari/Genesis Controller USB Adapter v0.2
author: ajacocks
2 layer board of 3.24 x 1.26 inches (82.2 x 32.0 mm)
Uploaded:
October 11, 2014
Shared:
October 11, 2014
Total Price:
$20.40
USB adapter to allow use of Atari- or Genesis-style joysticks and control pads.
USB adapter to allow use of Atari- or Genesis-style joysticks and control pads.
SimplePDBv1
author: irun4fundotca
2 layer board of 2.29 x 2.29 inches (58.1 x 58.2 mm)
Uploaded:
August 26, 2014
Shared:
October 10, 2014
Total Price:
$26.20
Simple PDB v1 First revision before final changes were made
$25 and change for 3
Simple PDB v1 First revision before final changes were made
$25 and change for 3
Mobile Radio Power Controller
author: pilotingpete
2 layer board of 1.70 x 1.07 inches (43.1 x 27.2 mm)
Uploaded:
August 26, 2014
Shared:
October 10, 2014
Total Price:
$9.05
A smart controller to delay power on and power off of a mobile ham radio. Details at petemills.blogspot.com
A smart controller to delay power on and power off of a mobile ham radio. Details at petemills.blogspot.com
Atmega8 header
author: DannyH
2 layer board of 0.61 x 1.21 inches (15.5 x 30.7 mm)
Uploaded:
October 09, 2014
Shared:
October 09, 2014
Total Price:
$3.65
Breadboard header for Atmel Atmega88 AVR. Place this over the atmega and connect your programmer.
Breadboard header for Atmel Atmega88 AVR. Place this over the atmega and connect your programmer.
LPC812 breakout SWD V2014.10.09
author: SquantMuts
2 layer board of 1.23 x 0.63 inches (31.1 x 15.9 mm)
Uploaded:
October 09, 2014
Shared:
October 09, 2014
Total Price:
$3.80
LPC812 TSSOP20 breakout board with SWD/JTAG connector, crystal pad, 3.3V regulator and reset/ISP buttons. Github respository.
LPC812 TSSOP20 breakout board with SWD/JTAG connector, crystal pad, 3.3V regulator and reset/ISP buttons. Github respository.